डिवाइस का खास कोड डालने के लिए, रिकवरी सिस्टम में कई हुक शामिल होते हैं, ताकि OTA अपडेट, Android सिस्टम के अलावा डिवाइस के दूसरे हिस्सों को भी अपडेट कर सकते हैं (उदाहरण के लिए, बेसबैंड या रेडियो प्रोसेसर).
नीचे दिए गए सेक्शन और उदाहरणों में, पसंद के मुताबिक बनाए गए टार्डिस डिवाइस पसंद के मुताबिक बनाए गए हैं. yoyodyne वेंडर के तौर पर किया जा सकता है.
पार्टिशन मैप
Android 2.3 के बाद से, यह प्लैटफ़ॉर्म eMMc फ़्लैश डिवाइस और चलने वाले ext4 फ़ाइलसिस्टम के साथ काम करता है ट्रैक करने में मदद मिलती है. यह Memory ऐसी टेक्नोलॉजी डिवाइस (MTD) फ़्लैश डिवाइसों और yaffs2 के साथ भी काम करता है फ़ाइल सिस्टम भेजा जा सकता है.
विभाजन मैप फ़ाइल TARGET_Recovery_FSTAB द्वारा तय की गई है; इस फ़ाइल का इस्तेमाल दोनों और पैकेज बनाने के टूल भी शामिल हैं. मैप फ़ाइल का नाम BoardConfig.mk में TARGET_Recovery_FSTAB.
पार्टिशन की एक सैंपल फ़ाइल, इस तरह दिख सकती है:
device/yoyodyne/tardis/recovery.fstab
# mount point fstype device [device2] [options (3.0+ only)] /sdcard vfat /dev/block/mmcblk0p1 /dev/block/mmcblk0 /cache yaffs2 cache /misc mtd misc /boot mtd boot /recovery emmc /dev/block/platform/s3c-sdhci.0/by-name/recovery /system ext4 /dev/block/platform/s3c-sdhci.0/by-name/system length=-4096 /data ext4 /dev/block/platform/s3c-sdhci.0/by-name/userdata
With the exception of /sdcard
, which is optional, all mount points in this
example must be defined (devices may also add extra partitions). There are five supported
filesystem types:
- yaffs2
-
A yaffs2 filesystem atop an MTD flash device. "device" must be the name of the MTD partition
and must appear in
/proc/mtd
. - mtd
-
A raw MTD partition, used for bootable partitions such as boot and recovery. MTD is not
actually mounted, but the mount point is used as a key to locate the partition. "device"
must be the name of the MTD partition in
/proc/mtd
. - ext4
- An ext4 filesystem atop an eMMc flash device. "device" must be the path of the block device.
- emmc
- A raw eMMc block device, used for bootable partitions such as boot and recovery. Similar to the mtd type, eMMc is never actually mounted, but the mount point string is used to locate the device in the table.
- vfat
-
A FAT filesystem atop a block device, typically for external storage such as an SD card. The
device is the block device; device2 is a second block device the system attempts to mount if
mounting the primary device fails (for compatibility with SD cards which may or may not be
formatted with a partition table).
All partitions must be mounted in the root directory (i.e. the mount point value must begin with a slash and have no other slashes). This restriction applies only to mounting filesystems in recovery; the main system is free to mount them anywhere. The directories
/boot
,/recovery
, and/misc
should be raw types (mtd or emmc), while the directories/system
,/data
,/cache
, and/sdcard
(if available) should be filesystem types (yaffs2, ext4, or vfat).
Starting in Android 3.0, the recovery.fstab file gains an additional optional field, options. Currently the only defined option is length , which lets you explicitly specify the length of the partition. This length is used when reformatting the partition (e.g., for the userdata partition during a data wipe/factory reset operation, or for the system partition during installation of a full OTA package). If the length value is negative, then the size to format is taken by adding the length value to the true partition size. For instance, setting "length=-16384" means the last 16k of that partition will not be overwritten when that partition is reformatted. This supports features such as encryption of the userdata partition (where encryption metadata is stored at the end of the partition that should not be overwritten).
Note: The device2 and options fields are optional, creating ambiguity in parsing. If the entry in the fourth field on the line begins with a ‘/' character, it is considered a device2 entry; if the entry does not begin with a ‘/' character, it is considered an options field.
Boot animation
Device manufacturers have the ability to customize the animation shown when an Android device is booting. To do this, construct a .zip file organized and located according to the specifications in bootanimation format.
For Android Things devices, you may upload the zipped file in the Android Things console to have the images included in the selected product.
Note: These images must meet Android brand guidelines. For brand guidelines, refer to the Android section of the Partner Marketing Hub.
Recovery UI
To support devices with different available hardware (physical buttons, LEDs, screens, etc.), you can customize the recovery interface to display status and access the manually-operated hidden features for each device.
Your goal is to build a small static library with a couple of C++ objects to provide the
device-specific functionality. The file
bootable/recovery/default_device.cpp
is used by default, and makes a good
starting point to copy when writing a version of this file for your device.
Note: You might see a message saying No Command here. To toggle text, hold the power button while you hit the volume up button. If your devices doesn't have both buttons, long press any button to toggle text.
device/yoyodyne/tardis/recovery/recovery_ui.cpp
#include <linux/input.h> #include "common.h" #include "device.h" #include "screen_ui.h"
Header and item functions
The Device class requires functions for returning headers and items that appear in the hidden recovery menu. Headers describe how to operate the menu (i.e. controls to change/select the highlighted item).
static const char* HEADERS[] = { "Volume up/down to move highlight;", "power button to select.", "", NULL }; static const char* ITEMS[] = {"reboot system now", "apply update from ADB", "wipe data/factory reset", "wipe cache partition", NULL };
Note: Long lines are truncated (not wrapped), so keep the width of your device screen in mind.
Customize CheckKey
Next, define your device's RecoveryUI implementation. This example assumes the
tardis device has a screen, so you can inherit from the built-in
ScreenRecoveryUIimplementation (see instructions for
devices without a screen.) The only function to
customize from ScreenRecoveryUI is CheckKey()
, which does the initial
asynchronous key handling:
class TardisUI : public ScreenRecoveryUI { public: virtual KeyAction CheckKey(int key) { if (key == KEY_HOME) { return TOGGLE; } return ENQUEUE; } };
KEY constants
The KEY_* constants are defined in linux/input.h
. CheckKey()
is
called no matter what is going on in the rest of recovery: when the menu is toggled off, when
it is on, during package installation, during userdata wiping, etc. It can return one of four
constants:
- TOGGLE. Toggle the display of the menu and/or text log on or off
- REBOOT. Immediately reboot the device
- IGNORE. Ignore this keypress
- ENQUEUE. Enqueue this keypress to be consumed synchronously (i.e., by the recovery menu system if the display is enabled)
CheckKey()
is called each time a key-down event is followed by a key-up event for
the same key. (The sequence of events A-down B-down B-up A-up results only in
CheckKey(B)
being called.) CheckKey()
can call
IsKeyPressed()
, to find out if other keys are being held down. (In the above
sequence of key events, if CheckKey(B)
called IsKeyPressed(A)
it
would have returned true.)
CheckKey()
can maintain state in its class; this can be useful to detect
sequences of keys. This example shows a slightly more complex setup: the display is toggled by
holding down power and pressing volume-up, and the device can be rebooted immediately by
pressing the power button five times in a row (with no other intervening keys):
class TardisUI : public ScreenRecoveryUI { private: int consecutive_power_keys; public: TardisUI() : consecutive_power_keys(0) {} virtual KeyAction CheckKey(int key) { if (IsKeyPressed(KEY_POWER) && key == KEY_VOLUMEUP) { return TOGGLE; } if (key == KEY_POWER) { ++consecutive_power_keys; if (consecutive_power_keys >= 5) { return REBOOT; } } else { consecutive_power_keys = 0; } return ENQUEUE; } };
ScreenRecoveryUI
When using your own images (error icon, installation animation, progress bars) with
ScreenRecoveryUI, you can set the variable animation_fps
to control the speed in
frames per second (FPS) of animations.
Note: The current interlace-frames.py
script enables you to
store the animation_fps
information in the image itself. In earlier versions of
Android it was necessary to set animation_fps
yourself.
To set the variable animation_fps
, override the
ScreenRecoveryUI::Init()
function in your subclass. Set the value, then call the
parent Init()
function to complete initialization. The default value (20 FPS)
corresponds to the default recovery images; when using these images you don't need to provide
an Init()
function. For details on images, see
Recovery UI Images.
Device class
After you have a RecoveryUI implementation, define your device class (subclassed from the
built-in Device class). It should create a single instance of your UI class and return that
from the GetUI()
function:
class TardisDevice : public Device { private: TardisUI* ui; public: TardisDevice() : ui(new TardisUI) { } RecoveryUI* GetUI() { return ui; }
StartRecovery
The StartRecovery()
method is called at the start of recovery, after the UI has
been initialized and after the arguments have been parsed, but before any action has been
taken. The default implementation does nothing, so you do not need to provide this in your
subclass if you have nothing to do:
void StartRecovery() { // ... do something tardis-specific here, if needed .... }
Supply and manage recovery menu
The system calls two methods to get the list of header lines and the list of items. In this implementation, it returns the static arrays defined at the top of the file:
const char* const* GetMenuHeaders() { return HEADERS; } const char* const* GetMenuItems() { return ITEMS; }
HandleMenuKey
Next, provide a HandleMenuKey()
function, which takes a keypress and the current
menu visibility, and decides what action to take:
int HandleMenuKey(int key, int visible) { if (visible) { switch (key) { case KEY_VOLUMEDOWN: return kHighlightDown; case KEY_VOLUMEUP: return kHighlightUp; case KEY_POWER: return kInvokeItem; } } return kNoAction; }
The method takes a key code (which has previously been processed and enqueued by the
CheckKey()
method of the UI object), and the current state of the menu/text log
visibility. The return value is an integer. If the value is 0 or higher, that is taken as the
position of a menu item, which is invoked immediately (see the
InvokeMenuItem()
method below). Otherwise it can be one of the following
predefined constants:
- kHighlightUp. Move the menu highlight to the previous item
- kHighlightDown. Move the menu highlight to the next item
- kInvokeItem. Invoke the currently highlighted item
- kNoAction. Do nothing with this keypress
As implied by the visible argument, HandleMenuKey()
is called even if the menu is
not visible. Unlike CheckKey()
, it is not called while recovery is doing
something such as wiping data or installing a package—it's called only when recovery is idle
and waiting for input.
Trackball mechanisms
If your device has a trackball-like input mechanism (generates input events with type EV_REL
and code REL_Y), recovery synthesizes KEY_UP and KEY_DOWN keypresses whenever the
trackball-like input device reports motion in the Y axis. All you need to do is map KEY_UP and
KEY_DOWN events onto menu actions. This mapping does not happen for
CheckKey()
, so you can't use trackball motions as triggers for rebooting or
toggling the display.
Modifier keys
To check for keys being held down as modifiers, call the IsKeyPressed()
method
of your own UI object. For example, on some devices pressing Alt-W in recovery would start a
data wipe whether the menu was visible or not. YOu could implement like this:
int HandleMenuKey(int key, int visible) { if (ui->IsKeyPressed(KEY_LEFTALT) && key == KEY_W) { return 2; // position of the "wipe data" item in the menu } ... }
Note: If visible is false, it doesn't make sense to return the special values that manipulate the menu (move highlight, invoke highlighted item) since the user can't see the highlight. However, you can return the values if desired.
InvokeMenuItem
Next, provide an InvokeMenuItem()
method that maps integer positions in the array
of items returned by GetMenuItems()
to actions. For the array of items in the
tardis example, use:
BuiltinAction InvokeMenuItem(int menu_position) { switch (menu_position) { case 0: return REBOOT; case 1: return APPLY_ADB_SIDELOAD; case 2: return WIPE_DATA; case 3: return WIPE_CACHE; default: return NO_ACTION; } }
This method can return any member of the BuiltinAction enum to tell the system to take that action (or the NO_ACTION member if you want the system to do nothing). This is the place to provide additional recovery functionality beyond what's in the system: Add an item for it in your menu, execute it here when that menu item is invoked, and return NO_ACTION so the system does nothing else.
BuiltinAction contains the following values:
- NO_ACTION. Do nothing.
- REBOOT. Exit recovery and reboot the device normally.
- APPLY_EXT, APPLY_CACHE, APPLY_ADB_SIDELOAD. Install an update package from various places. For details, see Sideloading.
- WIPE_CACHE. Reformat the cache partition only. No confirmation required as this is relatively harmless.
- WIPE_DATA. Reformat the userdata and cache partitions, also known as a factory data reset. The user is asked to confirm this action before proceeding.
The last method, WipeData()
, is optional and is called whenever a data wipe
operation is initiated (either from recovery via the menu or when the user has chosen to do a
factory data reset from the main system). This method is called before the user data and cache
partitions are wiped. If your device stores user data anywhere other than those two
partitions, you should erase it here. You should return 0 to indicate success and another
value for failure, though currently the return value is ignored. The user data and cache
partitions are wiped whether you return success or failure.
int WipeData() { // ... do something tardis-specific here, if needed .... return 0; }
Make device
Finally, include some boilerplate at the end of the recovery_ui.cpp file for the
make_device()
function that creates and returns an instance of your Device class:
class TardisDevice : public Device { // ... all the above methods ... }; Device* make_device() { return new TardisDevice(); }
Build and link to device recovery
After completing the recovery_ui.cpp file, built it and link it to recovery on your device. In Android.mk, create a static library that contains only this C++ file:
device/yoyodyne/tardis/recovery/Android.mk
LOCAL_PATH := $(call my-dir) include $(CLEAR_VARS) LOCAL_MODULE_TAGS := eng LOCAL_C_INCLUDES += bootable/recovery LOCAL_SRC_FILES := recovery_ui.cpp # should match TARGET_RECOVERY_UI_LIB set in BoardConfig.mk LOCAL_MODULE := librecovery_ui_tardis include $(BUILD_STATIC_LIBRARY)
Then, in the board configuration for this device, specify your static library as the value of TARGET_RECOVERY_UI_LIB.
device/yoyodyne/tardis/BoardConfig.mk [...] # device-specific extensions to the recovery UI TARGET_RECOVERY_UI_LIB := librecovery_ui_tardis
Recovery UI images
The recovery user interface consists of images. Ideally, users never interact with the UI: During a normal update, the phone boots into recovery, fills the installation progress bar, and boots back into the new system without input from the user. In the event of a system update problem, the only user action that can be taken is to call customer care.
An image-only interface obviates the need for localization. However, as of Android 5.0 the update can display a string of text (e.g. "Installing system update...") along with the image. For details, see Localized recovery text.
Android 5.0 and later
The Android 5.0 and later recovery UI uses two main images: the error image and the installing animation.
![]() Figure 1. icon_error.png |
![]() Figure 2. icon_installing.png |
The installing animation is represented as a single PNG image with different frames of the
animation interlaced by row (which is why Figure 2 appears squished). For example, for a
200x200 seven-frame animation, create a single 200x1400 image where first frame is rows 0, 7,
14, 21, ...; the second frame is rows 1, 8, 15, 22, ...; etc. The combined image includes a
text chunk that indicates the number of animation frames and the number of frames per second
(FPS). The tool bootable/recovery/interlace-frames.py
takes a set of input frames
and combines them into the necessary composite image used by recovery.
Default images are available in different densities and are located in
bootable/recovery/res-$DENSITY/images
(e.g.,
bootable/recovery/res-hdpi/images
). To use a static image during installation,
you need only provide the icon_installing.png image and set the number of frames in the
animation to 0 (the error icon is not animated; it is always a static image).
Android 4.x and earlier
The Android 4.x and earlier recovery UI uses the error image (shown above) and the installing animation plus several overlay images:
![]() Figure 3. icon_installing.png |
![]() Figure 4. icon-installing_overlay01.png |
![]() Figure 5. icon_installing_overlay07.png |
During installation, the on-screen display is constructed by drawing the icon_installing.png image, then drawing one of the overlay frames on top of it at the proper offset. Here, a red box is superimposed to highlight where the overlay is placed on top of the base image:
![]() Figure 6. Installing animation frame 1 (icon_installing.png + icon_installing_overlay01.png) |
![]() Figure 7. Installing animation frame 7 (icon_installing.png + icon_installing_overlay07.png) |
Subsequent frames are displayed by drawing only the next overlay image atop what's already there; the base image is not redrawn.
The number of frames in the animation, desired speed, and x- and y-offsets of the overlay
relative to the base are set by member variables of the ScreenRecoveryUI class. When using
custom images instead of default images, override the Init()
method in your
subclass to change these values for your custom images (for details, see
ScreenRecoveryUI). The script
bootable/recovery/make-overlay.py
can assist in converting a set of image frames
to the "base image + overlay images" form needed by recovery, including computing of the
necessary offsets.
Default images are located in bootable/recovery/res/images
. To use a static image
during installation, you need only provide the icon_installing.png image and set the number of
frames in the animation to 0 (the error icon is not animated; it is always a static image).
Localized recovery text
Android 5.x displays a string of text (e.g., "Installing system update...") along with the image. When the main system boots into recovery it passes the user's current locale as a command-line option to recovery. For each message to display, recovery includes a second composite image with pre-rendered text strings for that message in each locale.
Sample image of recovery text strings:
![image of recovery text](https://source.android.google.cn/static/docs/core/ota/images/installing_text.png?authuser=1&hl=hi)
Figure 8. Localized text for recovery messages
Recovery text can display the following messages:
- Installing system update...
- Error!
- Erasing... (when doing a data wipe/factory reset)
- No command (when a user boots into recovery manually)
The Android app in bootable/recovery/tools/recovery_l10n/
renders localizations
of a message and creates the composite image. For details on using this app, refer to the
comments in
bootable/recovery/tools/recovery_l10n/src/com/android/recovery_l10n/Main.java
.
When a user boots into recovery manually, the locale might not be available and no text is displayed. Do not make the text messages critical to the recovery process.
Note: The hidden interface that displays log messages and allows the user to select actions from the menu is available only in English.
Progress bars
Progress bars can appear below the main image (or animation). The progress bar is made by combining two input images, which must be of the same size:
![empty progress bar](https://source.android.google.cn/static/docs/core/ota/images/progress_empty.png?authuser=1&hl=hi)
Figure 9. progress_empty.png
![full progress bar](https://source.android.google.cn/static/docs/core/ota/images/progress_fill.png?authuser=1&hl=hi)
Figure 10. progress_fill.png
The left end of the fill image is displayed next to the right end of the empty image to make the progress bar. The position of the boundary between the two images is changed to indicate the progress. For example, with the above pairs of input images, display:
![progress bar at 1%](https://source.android.google.cn/static/docs/core/ota/images/progress_1.png?authuser=1&hl=hi)
Figure 11. Progress bar at 1%>
![progress bar at 10%](https://source.android.google.cn/static/docs/core/ota/images/progress_10.png?authuser=1&hl=hi)
Figure 12. Progress bar at 10%
![progress bar at 50%](https://source.android.google.cn/static/docs/core/ota/images/progress_50.png?authuser=1&hl=hi)
Figure 13. Progress bar at 50%
You can provide device-specific versions of these images by placing them into (in this
example) device/yoyodyne/tardis/recovery/res/images
. Filenames must match the ones listed above; when a file is found in that directory, the
build system uses it in preference to the corresponding default image. Only PNGs in RGB or
RGBA format with 8-bit color depth are supported.
Note: In Android 5.x, if the locale is known to recovery and is a right-to-left (RTL) language (Arabic, Hebrew, etc.), the progress bar fills from right to left.
Devices without screens
Not all Android devices have screens. If your device is a headless appliance or has an audio-only interface, you may need to do more extensive customization of recovery UI. Instead of creating a subclass of ScreenRecoveryUI, subclass its parent class RecoveryUI directly.
RecoveryUI has methods for handling a lower-level UI operations such as "toggle the display,"
"update the progress bar," "show the menu," "change the menu selection," etc. You can override
these to provide an appropriate interface for your device. Maybe your device has LEDs where
you can use different colors or patterns of flashing to indicate state, or maybe you can play
audio. (Perhaps you don't want to support a menu or the "text display" mode at all; you can
prevent accessing them with CheckKey()
and
HandleMenuKey()
implementations that never toggle the display on or select a menu
item. In this case, many of the RecoveryUI methods you need to provide can just be empty
stubs.)
See bootable/recovery/ui.h
for the declaration of RecoveryUI to see what methods
you must support. RecoveryUI is abstract—some methods are pure virtual and must be provided by
subclasses—but it does contain the code to do processing of key inputs. You can override that
too, if your device doesn't have keys or you want to process them differently.
Updater
You can use device-specific code in the installation of the update package by providing your own extension functions that can be called from within your updater script. Here's a sample function for the tardis device:
device/yoyodyne/tardis/recovery/recovery_updater.c
#include <stdlib.h> #include <string.h> #include "edify/expr.h"
Every extension function has the same signature. The arguments are the name by which the
function was called, a State*
cookie, the number of incoming arguments, and an
array of Expr*
pointers representing the arguments. The return value is a
newly-allocated Value*
.
Value* ReprogramTardisFn(const char* name, State* state, int argc, Expr* argv[]) { if (argc != 2) { return ErrorAbort(state, "%s() expects 2 args, got %d", name, argc); }
Your arguments have not been evaluated at the time your function is called—your function's
logic determines which of them get evaluated and how many times. Thus, you can use extension
functions to implement your own control structures. Call Evaluate()
to evaluate
an Expr*
argument, returning a Value*
. If Evaluate()
returns NULL, you should free any resources you're holding and immediately return NULL (this
propagates aborts up the edify stack). Otherwise, you take ownership of the Value returned and
are responsible for eventually calling
FreeValue()
on it.
Suppose the function needs two arguments: a string-valued key and a blob-valued image. You could read arguments like this:
Value* key = EvaluateValue(state, argv[0]); if (key == NULL) { return NULL; } if (key->type != VAL_STRING) { ErrorAbort(state, "first arg to %s() must be string", name); FreeValue(key); return NULL; } Value* image = EvaluateValue(state, argv[1]); if (image == NULL) { FreeValue(key); // must always free Value objects return NULL; } if (image->type != VAL_BLOB) { ErrorAbort(state, "second arg to %s() must be blob", name); FreeValue(key); FreeValue(image) return NULL; }
Checking for NULL and freeing previously evaluated arguments can get tedious for multiple
arguments. The ReadValueArgs()
function can make this easier. Instead of the code
above, you could have written this:
Value* key; Value* image; if (ReadValueArgs(state, argv, 2, &key, &image) != 0) { return NULL; // ReadValueArgs() will have set the error message } if (key->type != VAL_STRING || image->type != VAL_BLOB) { ErrorAbort(state, "arguments to %s() have wrong type", name); FreeValue(key); FreeValue(image) return NULL; }
ReadValueArgs()
doesn't do type-checking, so you must do that here; it's more
convenient to do it with one if statement at the cost of producing a somewhat less
specific error message when it fails. But ReadValueArgs()
does handle evaluating
each argument and freeing all the previously-evaluated arguments (as well as setting a useful
error message) if any of the evaluations fail. You can use a
ReadValueVarArgs()
convenience function for evaluating a variable number of
arguments (it returns an array of Value*
).
After evaluating the arguments, do the work of the function:
// key->data is a NUL-terminated string // image->data and image->size define a block of binary data // // ... some device-specific magic here to // reprogram the tardis using those two values ...
The return value must be a Value*
object; ownership of this object will pass to
the caller. The caller takes ownership of any data pointed to by this
Value*
—specifically the datamember.
In this instance, you want to return a true or false value to indicate success. Remember the
convention that the empty string is false and all other strings are true. You
must malloc a Value object with a malloc'd copy of the constant string to return, since the
caller will free()
both. Don't forget to call FreeValue()
on the
objects you got by evaluating your arguments!
FreeValue(key); FreeValue(image); Value* result = malloc(sizeof(Value)); result->type = VAL_STRING; result->data = strdup(successful ? "t" : ""); result->size = strlen(result->data); return result; }
The convenience function StringValue()
wraps a string into a new Value object.
Use to write the above code more succinctly:
FreeValue(key); FreeValue(image); return StringValue(strdup(successful ? "t" : "")); }
To hook functions into the edify interpreter, provide the function
Register_foo
where foo is the name of the static library containing
this code. Call RegisterFunction()
to register each extension function. By
convention, name device-specific functions device.whatever
to avoid
conflicts with future built-in functions added.
void Register_librecovery_updater_tardis() { RegisterFunction("tardis.reprogram", ReprogramTardisFn); }
You can now configure the makefile to build a static library with your code. (This is the same makefile used to customize the recovery UI in the previous section; your device may have both static libraries defined here.)
device/yoyodyne/tardis/recovery/Android.mk
include $(CLEAR_VARS) LOCAL_SRC_FILES := recovery_updater.c LOCAL_C_INCLUDES += bootable/recovery
The name of the static library must match the name of the
Register_libname
function contained within it.
LOCAL_MODULE := librecovery_updater_tardis include $(BUILD_STATIC_LIBRARY)
Finally, configure the build of recovery to pull in your library. Add your library to
TARGET_RECOVERY_UPDATER_LIBS (which may contain multiple libraries; they all get registered).
If your code depends on other static libraries that are not themselves edify extensions (i.e.,
they don't have a Register_libname
function), you can list those in
TARGET_RECOVERY_UPDATER_EXTRA_LIBS to link them to updater without calling their
(non-existent) registration function. For example, if your device-specific code wanted to use
zlib to decompress data, you would include libz here.
device/yoyodyne/tardis/BoardConfig.mk
[...] # add device-specific extensions to the updater binary TARGET_RECOVERY_UPDATER_LIBS += librecovery_updater_tardis TARGET_RECOVERY_UPDATER_EXTRA_LIBS +=
The updater scripts in your OTA package can now call your function as any other. To reprogram
your tardis device, the update script might contain:
tardis.reprogram("the-key", package_extract_file("tardis-image.dat"))
. This uses
the single-argument version of the built-in function package_extract_file()
,
which returns the contents of a file extracted from the update package as a blob to produce
the second argument to the new extension function.
OTA package generation
The final component is getting the OTA package generation tools to know about your device-specific data and emit updater scripts that include calls to your extension functions.
First, get the build system to know about a device-specific blob of data. Assuming your data
file is in device/yoyodyne/tardis/tardis.dat
, declare the following in your
device's AndroidBoard.mk:
device/yoyodyne/tardis/AndroidBoard.mk
[...] $(call add-radio-file,tardis.dat)
You could also put it in an Android.mk instead, but then it must to be guarded by a device check, since all the Android.mk files in the tree are loaded no matter what device is being built. (If your tree includes multiple devices, you only want the tardis.dat file added when building the tardis device.)
device/yoyodyne/tardis/Android.mk
[...] # an alternative to specifying it in AndroidBoard.mk ifeq (($TARGET_DEVICE),tardis) $(call add-radio-file,tardis.dat) endif
These are called radio files for historical reasons; they may have nothing to do with the
device radio (if present). They are simply opaque blobs of data the build system copies into
the target-files .zip used by the OTA generation tools. When you do a build, tardis.dat is
stored in the target-files.zip as RADIO/tardis.dat
. You can call
add-radio-file
multiple times to add as many files as you want.
Python module
To extend the release tools, write a Python module (must be named releasetools.py) the tools can call into if present. Example:
device/yoyodyne/tardis/releasetools.py
import common def FullOTA_InstallEnd(info): # copy the data into the package. tardis_dat = info.input_zip.read("RADIO/tardis.dat") common.ZipWriteStr(info.output_zip, "tardis.dat", tardis_dat) # emit the script code to install this data on the device info.script.AppendExtra( """tardis.reprogram("the-key", package_extract_file("tardis.dat"));""")
A separate function handles the case of generating an incremental OTA package. For this example, suppose you need to reprogram the tardis only when the tardis.dat file has changed between two builds.
def IncrementalOTA_InstallEnd(info): # copy the data into the package. source_tardis_dat = info.source_zip.read("RADIO/tardis.dat") target_tardis_dat = info.target_zip.read("RADIO/tardis.dat") if source_tardis_dat == target_tardis_dat: # tardis.dat is unchanged from previous build; no # need to reprogram it return # include the new tardis.dat in the OTA package common.ZipWriteStr(info.output_zip, "tardis.dat", target_tardis_dat) # emit the script code to install this data on the device info.script.AppendExtra( """tardis.reprogram("the-key", package_extract_file("tardis.dat"));""")
Module functions
You can provide the following functions in the module (implement only the ones you need).
FullOTA_Assertions()
- Called near the start of generating a full OTA. This is a good place to emit assertions about the current state of the device. Do not emit script commands that make changes to the device.
FullOTA_InstallBegin()
- Called after all the assertions about the device state have passed but before any changes have been made. You can emit commands for device-specific updates that must run before anything else on the device has been changed.
FullOTA_InstallEnd()
- Called at the end of the script generation, after the script commands to update the boot and system partitions have been emitted. You can also emit additional commands for device-specific updates.
IncrementalOTA_Assertions()
-
Similar to
FullOTA_Assertions()
but called when generating an incremental update package. IncrementalOTA_VerifyBegin()
- Called after all assertions about the device state have passed but before any changes have been made. You can emit commands for device-specific updates that must run before anything else on the device has been changed.
IncrementalOTA_VerifyEnd()
- Called at the end of the verification phase, when the script has finished confirming the files it is going to touch have the expected starting contents. At this point nothing on the device has been changed. You can also emit code for additional device-specific verifications.
IncrementalOTA_InstallBegin()
- Called after files to be patched have been verified as having the expected before state but before any changes have been made. You can emit commands for device-specific updates that must run before anything else on the device has been changed.
IncrementalOTA_InstallEnd()
- Similar to its full OTA package counterpart, this is called at the end of the script generation, after the script commands to update the boot and system partitions have been emitted. You can also emit additional commands for device-specific updates.
Note: If the device loses power, OTA installation may restart from the beginning. Be prepared to cope with devices on which these commands have already been run, fully or partially.
Pass functions to info objects
Pass functions to a single info object that contains various useful items:
-
info.input_zip. (Full OTAs only) The
zipfile.ZipFile
object for the input target-files .zip. -
info.source_zip. (Incremental OTAs only) The
zipfile.ZipFile
object for the source target-files .zip (the build already on the device when the incremental package is being installed). -
info.target_zip. (Incremental OTAs only) The
zipfile.ZipFile
object for the target target-files .zip (the build the incremental package puts on the device). -
info.output_zip. Package being created; a
zipfile.ZipFile
object opened for writing. Use common.ZipWriteStr(info.output_zip, filename, data) to add a file to the package. -
info.script. Script object to which you can append commands. Call
info.script.AppendExtra(script_text)
to output text into the script. Make sure output text ends with a semicolon so it does not run into commands emitted afterwards.
For details on the info object, refer to the Python Software Foundation documentation for ZIP archives.
Specify module location
Specify the location of your device's releasetools.py script in your BoardConfig.mk file:
device/yoyodyne/tardis/BoardConfig.mk
[...] TARGET_RELEASETOOLS_EXTENSIONS := device/yoyodyne/tardis
If TARGET_RELEASETOOLS_EXTENSIONS is not set, it defaults to the
$(TARGET_DEVICE_DIR)/../common
directory (device/yoyodyne/common
in this example). It's best to explicitly define the location of the releasetools.py script.
When building the tardis device, the releasetools.py script is included in the target-files
.zip file (META/releasetools.py
).
When you run the release tools (either img_from_target_files
or
ota_from_target_files
), the releasetools.py script in the target-files .zip, if
present, is preferred over the one from the Android source tree. You can also explicitly
specify the path to the device-specific extensions with the -s
(or
--device_specific
) option, which takes the top priority. This enables you to
correct errors and make changes in the releasetools extensions and apply those changes to old
target-files.
Now, when you run ota_from_target_files
, it automatically picks up the
device-specific module from the target_files .zip file and uses it when generating OTA
packages:
./build/make/tools/releasetools/ota_from_target_files \
-i PREVIOUS-tardis-target_files.zip \
dist_output/tardis-target_files.zip \
incremental_ota_update.zip
इसके अलावा, जब आप दौड़ते हैं, तो आप डिवाइस के हिसाब से एक्सटेंशन तय कर सकते हैं
ota_from_target_files
.
./build/make/tools/releasetools/ota_from_target_files \
-s device/yoyodyne/tardis \
-i PREVIOUS-tardis-target_files.zip \
dist_output/tardis-target_files.zip \
incremental_ota_update.zip
ध्यान दें: विकल्पों की पूरी सूची देखने के लिए,
इसमें ota_from_target_files
टिप्पणियां:
build/make/tools/releasetools/ota_from_target_files
.
साइडलोडिंग मैकेनिज़्म
बिना अपडेट पैकेज को मैन्युअल तरीके से इंस्टॉल करने के लिए, रिकवरी में साइडलोडिंग का तरीका होता है इसे मुख्य सिस्टम से ओवर द एयर डाउनलोड करने के लिए किया जा सकता है. साइडलोडिंग का इस्तेमाल, डीबग करने या साइट बनाने के लिए किया जा सकता है उन डिवाइस में किए गए बदलाव जिनसे मुख्य सिस्टम चालू नहीं हो सकता.
अब तक, डिवाइस के एसडी कार्ड से पैकेज लोड करके, अलग से लोड किए जाते थे; इंच गैर-बूटिंग डिवाइस के मामले में, तो किसी अन्य उपकरण का उपयोग करके पैकेज को SD कार्ड पर रखा जा सकता है कंप्यूटर और फिर डिवाइस में डाला गया एसडी कार्ड. बिना Android डिवाइस के इस्तेमाल करने के लिए हटाए जा सकने वाला बाहरी स्टोरेज, रिकवरी टूल को अलग से लोड करने के लिए दो और तरीके अपनाए जा सकते हैं: कैश मेमोरी वाले पार्टिशन से पैकेज लोड करना और adb का इस्तेमाल करके उन्हें यूएसबी पर लोड करना.
अलग से लोड करने के हर तरीके को शुरू करने के लिए, आपके डिवाइस का Device::InvokeMenuItem()
तरीका
createdinAction के नीचे दिए गए मान दिखा सकते हैं:
-
लागू_EXT. किसी अपडेट पैकेज को बाहरी स्टोरेज से अलग से लोड करें (
/sdcard
डायरेक्ट्री). रिकवरी.fstab को/sdcard
माउंट पॉइंट के तौर पर सेट करना ज़रूरी है. यह है यह सुविधा उन डिवाइसों पर इस्तेमाल नहीं की जा सकती जो/data
(या कुछ) के सिमलिंक वाले एसडी कार्ड को एम्युलेट करते हों एक ही तरह का तरीका)./data
आम तौर पर, रिकवरी के लिए उपलब्ध नहीं होता, क्योंकि यह एन्क्रिप्ट किया जा सकता है. रिकवरी यूज़र इंटरफ़ेस (यूआई),/sdcard
में .zip फ़ाइलों का मेन्यू दिखाता है और उपयोगकर्ता को किसी एक को चुनने की सुविधा देता है. -
लागू_CACHE. यह
/sdcard
से पैकेज लोड करने के जैसा ही होता है, लेकिन इसमें/cache
डायरेक्ट्री (जो रिकवरी के लिए हमेशा उपलब्ध है) का इस्तेमाल किया जाता है आज़माएं. सामान्य सिस्टम से,/cache
को सिर्फ़ वे लोग लिख सकते हैं जिनके पास खास अधिकार हैं, और अगर डिवाइस बूट नहीं किया जा सकता है, तो/cache
डायरेक्ट्री को बिलकुल भी (जिसकी वजह से काम करने की यह प्रक्रिया सीमित हो जाती है). -
लागू_ADB_SIDELOAD. उपयोगकर्ता को USB केबल के ज़रिए डिवाइस में पैकेज भेजने की अनुमति देता है और
एडीबी डेवलपमेंट टूल पर ध्यान देते हैं. इस तरीके को शुरू करने पर, रिकवरी का अपना मिनी शुरू हो जाता है
का उपयोग कर सकते हैं, ताकि कनेक्ट किए गए होस्ट कंप्यूटर पर adb इससे बात की जा सके. यह मिनी
वर्शन में सिर्फ़ एक निर्देश काम करता है:
adb sideload filename
. नाम वाली फ़ाइल, होस्ट मशीन से डिवाइस पर भेजी जाती है. इसके बाद, फ़ाइल की पुष्टि की जाती है और इंस्टॉल करता है, जैसे कि उसे लोकल स्टोरेज में रखा गया हो.
कुछ सावधानियां:
- सिर्फ़ यूएसबी ट्रांसपोर्ट काम करता है.
-
अगर आपका रिकवरी टूल, adbd को सामान्य तरीके से चलाता है (आम तौर पर, userdebug और eng बिल्ड के लिए ऐसा किया जाता है), तो यह
जब डिवाइस, adb अलग से लोड करने वाले मोड में होगा, तब शट डाउन हो जाएगा. साथ ही, adb के दौरान यह रीस्टार्ट हो जाएगा
अलग से लोड करने के लिए, पैकेज इकट्ठा हो गया है. adb अलग से लोड करने वाले मोड में, कोई adb निर्देश नहीं
sideload
से ज़्यादा काम करते हैं (logcat
,reboot
,push
,pull
,shell
वगैरह. -
इस डिवाइस पर, adb अलग से लोड करने वाले मोड से बाहर नहीं निकला जा सकता. रद्द करने के लिए, भेजा जा सकता है
पैकेज के तौर पर
/dev/null
(या कोई और चीज़ जो मान्य पैकेज नहीं है) और तो डिवाइस इसकी पुष्टि नहीं कर पाएगा और इंस्टॉलेशन प्रक्रिया नहीं रोक देगा. RecoveryUI लागू करने काCheckKey()
तरीका, कीप्रेस के लिए कॉल किया जाता रहेगा, ताकि डिवाइस को फिर से चालू करने और adb अलग से लोड करने वाले मोड में काम करने वाली कुंजी का क्रम तय किया जा सके.