支持的系统属性

本页面列出了 VHAL 中支持的系统属性。VHAL 支持的属性必须是下方列表中的系统属性或供应商属性。在 Android 14 及更高版本中，属性定义在 hardware/interfaces/automotive/vehicle/aidl_property/android/hardware/automotive/vehicle/VehicleProperty.aidl 中定义。

属性定义在 AIDL 接口 (android.hardware.automotive.vehicle.property) 中定义，该接口与 VHAL 接口 (android.hardware.automotive.vehicle) 是分开的。VHAL 实现和 VHAL 客户端必须依赖这两个接口。

自动生成的访问模式和更改模式

在 Android 14 及更高版本中，为了支持 VHAL 实现，我们提供了自动生成的 C++ 头文件和 Java 类文件，其中包含允许对系统属性使用的更改模式或访问模式。供应商 VHAL 实现可以使用这些属性来确保属性配置符合规范。

A 到 D

ADAPTIVE_CRUISE_CONTROL_LEAD_VEHICLE_MEASURED_DISTANCE

使用自适应巡航控制 (ACC) 或预测性巡航控制 (PCC) 时测量的与前车的距离。返回前车最后端点与 ACC 车辆最前端点之间的测量距离，单位为毫米。必须定义 VehicleAreaConfig 中的 maxInt32Value 和 minInt32Value。minInt32Value 应为 0。maxInt32Value 应填充距离传感器支持的最大范围。此值应为非负值。

如果未检测到前车（即，没有前车；或与前车相距太远，传感器无法检测到），此属性应返回 StatusCode.NOT_AVAILABLE

如果此属性因 CC 处于停用状态（例如 StatusCode#NOT_AVAILABLE_DISABLED 为 false）而不可用，则必须返回 StatusCode#NOT_AVAILABLE_DISABLED。如果实现了 CRUISE_CONTROL_STATE 且状态设置为 ErrorState 值，则此属性必须返回与 ErrorState 值一致的 StatusCode。例如，如果 CRUISE_CONTROL_STATE 设置为 ErrorState#NOT_AVAILABLE_SPEED_LOW，则此属性必须返回 StatusCode#NOT_AVAILABLE_SPEED_LOW

更改模式：CONTINUOUS
访问模式：READ
枚举类型：无
单位类型：VehicleUnit:MILLIMETER
版本：Android 14

ADAPTIVE_CRUISE_CONTROL_TARGET_TIME_GAP

ACC 或 PCC 的当前目标时间间隔（以毫秒为单位）。 此属性应指定与前车的目标时间间隔。此时间间隔定义为，从前车的最后端点行驶到 ACC 车辆的最前端点所需的时间。与前车的实际时间间隔可能会高于或低于此值。

应在 configArray 中按升序指定可为目标时间间隔设置的值。所有值都必须为正数。如果该属性可写入，则所有值都必须可写入。如果此属性因 CC 处于停用状态（例如 CRUISE_CONTROL_ENABLED 为 false）而不可用，则必须返回 StatusCode#NOT_AVAILABLE_DISABLED

如果实现了 CRUISE_CONTROL_STATE 且状态设置为 ErrorState 值，则此属性必须返回与 ErrorState 值一致的 StatusCode。例如，如果 CRUISE_CONTROL_STATE 设置为 ErrorState#NOT_AVAILABLE_SPEED_LOW，则此属性必须返回 StatusCode#NOT_AVAILABLE_SPEED_LOW

此属性被定义为 VehiclePropertyAccess.READ_WRITE，但原始设备制造商 (OEM) 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：VehicleUnit:MILLI_SECS
版本：Android 14

ABS_ACTIVE

自动制动系统 (ABS) 处于启用状态。当 ABS 处于启用状态时设置为 true，当 ABS 处于关闭状态时重置为 false。此属性可根据 ABS 系统的实时状态间歇性设置（脉冲式）。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

ANDROID_EPOCH_TIME

采用纪元时间编码的当前日期和时间（以毫秒为单位）。此值表示自世界协调时间 (UTC) 1970 年 1 月 1 日以来经过的毫秒数。

此值表示自世界协调时间 (UTC) 1970 年 1 月 1 日以来经过的毫秒数。 如果 VHAL 支持此属性，CarServices 会向此值执行 WRITE，以向 VHAL 提供 Android 系统的时间。这对于使其他车载系统（仪表盘时钟）与 Android 时间保持同步非常有用。

AAOS 会在启动期间对此属性执行一次 WRITE，之后仅会在时间源变化被传播时才会执行 WRITE。AAOS 会正确填充 VehiclePropValue.timestamp。AAOS 不会因时间自然流逝而发送更新。int64Values[0] 表示提供的 Unix 时间（以毫秒为单位）。

该属性可能需要超过 0 毫秒的时间才能通过堆栈传播，而拥有带着时间戳的属性有助于减少时移。因此，对于向该属性执行的所有 WRITE，时间戳都可用于消除这种时移：

drift = elapsedTime - PropValue.timestamp effectiveTime = PropValue.value.int64Values[0] + drift

更改模式：ON_CHANGE
访问模式：WRITE
枚举类型：无
单位类型：VehicleUnit:MILLI_SECS
版本：Android 13

AP_POWER_BOOTUP_REASON

用于报告当前开机原因的属性。这是一个 STATIC 属性，在设备关机前的整个时间段内都不会改变。例如，在系统因车门解锁而自动开机后，即使用户再次按下电源按钮，开机原因仍会保持为 VehicleApPowerBootupReason#USER_UNLOCK，int32Values[0] 必须为 VehicleApPowerBootupReason

更改模式：STATIC
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

AP_POWER_STATE_REPORT

用于报告应用处理器电源状态的属性。 假设 AP 的电源状态由单独的电源控制器控制。

• int32Values[0] VehicleApPowerStateReport 枚举值
• int32Values[1] 唤醒所需的时间，以毫秒 (ms) 为单位，如有必要的话（否则为 0）

更改模式：ON_CHANGE
访问模式：READ_WRITE
枚举类型：无
单位类型：无
版本：Android 13

AP_POWER_STATE_REQ

用于控制应用处理器电源状态的属性。 假设 AP 的电源状态由单独的电源控制器控制。对于配置信息，VehiclePropConfig.configArray 必须在 VehicleApPowerStateConfigFlag 中具有位标志组合值

• int32Values[0] VehicleApPowerStateReq 枚举值
• int32Values[1] 与每个状态相关的额外参数；如果未使用，则为 0。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

AUTOMATIC_EMERGENCY_BRAKING_ENABLED

启用或停用自动紧急制动 (AEB)。 设置为 true 可启用 AEB，设置为 false 可停用 AEB。当 AEB 处于启用状态时，车辆中的 ADAS 系统应保持开启并进行监控，以避免可能发生的碰撞。此属性应仅适用于车速较高的应用场景。如需启用低速自动紧急制动功能，应使用 LOW_SPEED_AUTOMATIC_EMERGENCY_BRAKING_ENABLED。

一般来说，AUTOMATIC_EMERGENCY_BRAKING_ENABLED 应始终返回 true 或 false。如果该功能因某种临时状态（例如车速过低）而不可用，则必须通过 AUTOMATIC_EMERGENCY_BRAKING_STATE 属性中的 ErrorState 值传达此信息。

此属性被定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 14

AUTOMATIC_EMERGENCY_BRAKING_STATE

自动紧急制动 (AEB) 状态。返回 AEB 的当前状态。此属性必须始终返回 AutomaticEmergencyBrakingState 或 ErrorState 中定义的有效状态。它不得通过 StatusCode 显示错误，而必须改用受支持的错误状态。此属性应仅适用于车速较高的应用场景。如需表示低速自动紧急制动系统的状态，应使用 LOW_SPEED_AUTOMATIC_EMERGENCY_BRAKING_STATE。

如果 AEB 在启用刹车之前包含前向碰撞警告，这些警告必须通过前向碰撞警告 (FCW) 属性显示。

对于全局区域 ID (0)，必须定义 StatusCode#VehicleAreaConfig#supportedEnumValues 数组，除非同时支持 AutomaticEmergencyBrakingState（包括不推荐的 OTHER）和 ErrorState 的所有状态。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：ForwardCollisionWarningState/ErrorState
单位类型：无
版本：Android 14

BLIND_SPOT_WARNING_ENABLED

启用和停用盲点警告 (BSW)。 设置为 true 可启用 BSW，设置为 false 可停用 BSW。当 BSW 处于启用状态时，车辆中的 ADAS 系统应保持开启，并监控车辆的盲点区域是否有物体。

一般来说，BLIND_SPOT_WARNING_ENABLED 应始终返回 true 或 false。 如果该功能因某种临时状态（例如车速过低）而不可用，则必须通过 BLIND_SPOT_WARNING_STATE 属性中的 ErrorState 值传达此信息。

此属性定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 14

BLIND_SPOT_WARNING_STATE

盲点警告 (BSW) 状态。 返回 BSW 的当前状态。此属性必须始终返回 BlindSpotWarningState 或 ErrorState 中定义的有效状态。它不得通过 StatusCode 显示错误，而必须改用受支持的错误状态。

对于每个受支持的区域 ID，必须定义 StatusCode#VehicleAreaConfig#supportedEnumValues 数组，除非同时支持 BlindSpotWarningState（包括不推荐的 OTHER）和 ErrorState 的所有状态。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：BlindSpotWarningState/ErrorState
单位类型：无
版本：Android 14

CABIN_LIGHTS_STATE

返回车厢灯的状态。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：VehicleLightState
单位类型：无
版本：Android 13

CABIN_LIGHTS_SWITCH

车厢灯开关。 控制车厢灯的实体开关的位置。如果灯开着是因为门打开了或因为语音指令，则可能与 CABIN_LIGHTS_STATE 不同。例如，当开关处于关闭或自动位置时。

此属性被定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：VehicleLightSwitch
单位类型：无
版本：Android 13

CLUSTER_DISPLAY_STATE

更改仪表板屏幕的状态。

• 边界：用于渲染仪表集群 activity 的区域。
• 边衬区：activity 不应在该区域放置重要信息。

可能的值为：

• int32[0] 开启、关闭：0 - 关闭，1 - 开启，-1 - 随意
• int32[1] 边界 - 左：正数 - 左侧位置（以像素为单位）-1 - 随意（应设置所有边界字段）
• int32[2] 边界 - 上：与“左”格式相同
• int32[3] 边界 - 右：与“左”格式相同
• int32[4] 边界 - 下：与“左”格式相同
• int32[5] 边衬区 - 左：正数 - 实际左边衬区值（以像素为单位）-1 - 随意（应将所有边衬区字段设置为“随意”）
• int32[6] 边衬区 - 上：与“左”格式相同
• int32[7] 边衬区 - 右：与“左”格式相同
• int32[8] 边衬区 - 下：与“左”格式相同

更改模式：ON_CHANGE
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

CLUSTER_NAVIGATION_STATE

通知当前导航状态。字节：NavigationStateProto 的序列化消息。

更改模式：ON_CHANGE
访问模式：WRITE
枚举类型：
单位类型：无
版本：Android 13

CLUSTER_REPORT_STATE

报告当前显示状态和 ClusterUI 状态。 ClusterHome 在处理 CLUSTER_SWITCH_UI、CLUSTER_DISPLAY_STATE 时发送此消息。此外，ClusterHome 应在首次启动时发送此消息。当 ClusterOS 收到此消息时，如果内部预期与收到的消息不同，那么它应会再次发送 CLUSTER_SWITCH_UI、CLUSTER_DISPLAY_STATE 以匹配状态。

• int32[0] 开启/关闭：0 - 关闭，1 - 开启
• int32[1] 边界 - 左
• int32[2] 边界 - 上
• int32[3] 边界 - 右
• int32[4] 边界 - 下
• int32[5] 边衬区 - 左
• int32[6] 边衬区 - 上
• int32[7] 边衬区 - 右
• int32[8] 边衬区 - 下
• int32[9] 全屏或主屏幕中的 ClusterUI 类型。0 表示 ClusterHome。其他值则按照 OEM 的定义。
• int32[10] 子屏幕中的 ClusterUI 类型，如果当前显示两个界面的话。-1 表示该区域不再使用。字节：表示 ClusterUI 可用性的数组。0 表示不可用，1 表示可用。例如，如果汽车支持 OEM 定义的三个 ClusterUI（例如 HOME、MAPS 和 CALL），并且仅在移动网络可用时支持 CALL 界面。然后，如果网络可用，它发送 [1 1 1]；如果网络不可用，则发送 [1 1 0]。

更改模式：ON_CHANGE
访问模式：WRITE
枚举类型：VehicleLightSwitch
单位类型：无
版本：Android 13

CLUSTER_REQUEST_DISPLAY

用于更改仪表板显示屏状态以显示某些 ClusterUI 的请求。 当前显示状态为关闭时，ClusterHome 会将此消息发送到 ClusterOS，请求开启显示屏以显示特定的 ClusterUI。ClusterOS 应使用 CLUSTER_DISPLAY_STATE 响应此请求

• int32 要显示的 ClusterUI 类型

更改模式：ON_CHANGE
访问模式：WRITE
枚举类型：无
单位类型：无
版本：Android 13

CLUSTER_SWITCH_UI

在仪表板显示屏中启动 ClusterUI。

• int32 要显示的 ClusterUI 类型，0 表示 ClusterHome，即仪表集群显示屏的主屏幕，并为仪表集群显示屏提供默认界面和一种启动器功能。其他值则按照 OEM 的定义。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

CREATE_USER

创建 Android 用户后由 Android 系统调用。 HAL 可以使用此属性来创建其相应的用户。这是一个异步请求：Android 通过设置 VehiclePropValue 发出请求，HAL 必须通过属性更改进行响应，指明请求是成功还是失败。如果失败，Android 系统会移除该用户。

请求的格式由 CreateUserRequest 定义，响应的格式由 CreateUserResponse 定义。例如，如果系统有两位用户（0 和 10），并且创建了第三位用户（即临时访客），请求将如下所示：

• int32[0] 42 // 请求 ID
• int32[1] 11 // 所创建用户的 Android ID
• int32[2] 6 // 所创建用户的 Android 标志（临时访客）
• int32[3] 10 // 当前用户
• int32[4] 0 // 当前用户标志（无）
• int32[5] 3 // 用户数量
• int32[6] 0 // 第一位用户（用户 0）
• int32[7] 0 // 第一位用户标志（无）
• int32[8] 10 // 第二位用户（用户 10）
• int32[9] 0 // 第二位用户标志（无）
• int32[10] 11 // 第三位用户（用户 11）
• int32[11] 6 // 第三位用户标志（临时访客）字符串："ElGuesto" // 新用户的名称

如果请求成功，HAL 会返回：

• int32[0] 42 // 请求 ID
• int32[1] 1 // CreateUserStatus::SUCCESS

但如果失败，则返回：

• int32[0] 42 // 请求 ID
• int32[1] 2 // CreateUserStatus::FAILURE 字符串："D'OH!" //

含义是黑箱，并传递给调用方（例如设置界面），后者会执行适当的操作。

更改模式：ON_CHANGE
访问模式：READ_WRITE
枚举类型：无
单位类型：无
版本：Android 13

CRITICALLY_LOW_TIRE_PRESSURE

此属性表示每个轮胎的极低胎压阈值。它表示何时更换或修理轮胎。此值必须小于或等于 TIRE_PRESSURE 中的 minFloatValue。最小和最大属性值（minFloatValue 和 maxFloatValue）不适用于此属性。

更改模式：STATIC
访问模式：READ
枚举类型：无
单位类型：VehicleUnit:KILOPASCAL
版本：Android 13

CRUISE_CONTROL_COMMAND

WRITE 巡航控制 (CC) 指令。如需详细了解每个受支持的指令，请参阅 CruiseControlCommand。对于全局区域 ID (0)，必须定义 StatusCode#VehicleAreaConfig#supportedEnumValues 数组，除非同时支持 CruiseControlState 的所有状态。通过此属性发送的任何不受支持的指令都必须返回 StatusCode#INVALID_ARG。如果此属性因 CC 处于停用状态（例如 CRUISE_CONTROL_ENABLED 为 false）而不可用，则必须返回 StatusCode#NOT_AVAILABLE_DISABLED。如果实现了 CRUISE_CONTROL_STATE 且状态设置为 ErrorState 值，则此属性必须返回与 ErrorState 值一致的 StatusCode。例如，如果 CRUISE_CONTROL_STATE 设置为 ErrorState#NOT_AVAILABLE_SPEED_LOW，则此属性必须返回 StatusCode#NOT_AVAILABLE_SPEED_LOW

更改模式：ON_CHANGE
访问模式：WRITE
枚举类型：CruiseControlCommand
单位类型：无
版本：Android 14

CRUISE_CONTROL_ENABLED

启用或停用巡航控制 (CC)。 设置为 true 表示启用 CC，设置为 false 表示停用 CC。此属性由所有形式的 CruiseControlType 共享。当 CC 处于启用状态时，车辆中的 ADAS 系统应处于开启状态并响应指令。一般来说，CRUISE_CONTROL_ENABLED 应始终返回 true 或 false。如果该功能因某种临时状态（例如车速过低）而不可用，则必须通过 CRUISE_CONTROL_STATE 属性中的 ErrorState 值传达此信息。此属性被定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 14

CRUISE_CONTROL_STATE

巡航控制 (CC) 的当前状态。 此属性会返回 CC 当前的状态。通常，此属性应返回 CruiseControlState 或 ErrorState 中定义的有效状态。例如，如果该功能因某种临时状态而不可用，则应通过 ErrorState 传达此信息。对于全局区域 ID (0)，必须定义 VehicleAreaConfig#supportedEnumValue 数组，除非同时支持 CruiseControlState（包括不推荐的 OTHER）和 ErrorState 的所有状态。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：CruiseControlState/ErrorState
单位类型：无
版本：Android 14

CRUISE_CONTROL_TARGET_SPEED

巡航控制 (CC) 的当前目标速度。 OEM 应为此属性设置 minFloatValue 和 maxFloatValue 值，以定义最小和最大目标速度值。这些值必须是非负值。maxFloatValue 表示目标速度的上限。minFloatValue 表示目标速度的下限。如果此属性因 CC 处于停用状态（例如 CRUISE_CONTROL_ENABLED 为 false）而不可用，则必须返回 StatusCode#NOT_AVAILABLE_DISABLED。如果实现了 CRUISE_CONTROL_STATE 且状态设置为 ErrorState 值，则此属性必须返回与 ErrorState 值一致的 StatusCode。例如，如果 CRUISE_CONTROL_STATE 设置为 ErrorState#NOT_AVAILABLE_SPEED_LOW，则此属性必须返回 StatusCode#NOT_AVAILABLE_SPEED_LOW

更改模式：ON_CHANGE
访问模式：READ
枚举类型：无
单位类型：VehicleUnit:METER_PER_SEC
版本：Android 14

CRUISE_CONTROL_TYPE

巡航控制 (CC) 的当前类型。 当 CRUISE_CONTROL_ENABLED 为 true 时，此属性会返回当前启用的 CC 类型（例如标准 CC 和自适应 CC、预测性 CC）。通常，此属性应返回 CruiseControlType 或 ErrorState 中定义的有效状态。例如，如果该功能因某种临时状态而不可用，则应通过 ErrorState 传达此信息。对于全局区域 ID (0)，必须定义 StatusCode#VehicleAreaConfig#supportedEnumValues 数组，除非支持 CruiseControlType（包括不推荐的 OTHER）和 ErrorState 的所有状态。尝试将 CruiseControlType#OTHER 或 ErrorState WRITE 到此属性会抛出 IllegalArgumentException。此属性定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：CruiseControlType ErrorState
单位类型：无
版本：Android 14

CURRENT_GEAR

当前档位。在非手动情况下，所选档位可能与当前档位不符。例如，所选档位是 GEAR_DRIVE，而当前档位是 GEAR_1、GEAR_2 等档位中的一个，这反映了变速器当前运行的实际档位。配置数据中的值必须表示此车辆的受支持档位列表。例如，自动变速器的配置数据必须包含 {GEAR_NEUTRAL, GEAR_REVERSE, GEAR_PARK, GEAR_1, GEAR_2,...}，而手动变速器的列表必须为 {GEAR_NEUTRAL, GEAR_REVERSE, GEAR_1, GEAR_2,...}。此列表不必与 GEAR_SELECTION 中报告的受支持档位列表相同。

更改模式：ON_CHANGE
访问模式：READ
枚举类型：VehicleGear
单位类型：无
版本：Android 13

CURRENT_POWER_POLICY

向 VHAL 层通知当前电源政策。 当前电源政策发生变化时，汽车电源政策服务会设置此属性

string: "sample_policy_id" // power policy ID

更改模式：ON_CHANGE
访问模式：READ_WRITE
枚举类型：无
单位类型：无
版本：Android 13

DISABLED_OPTIONAL_FEATURES

允许在 VHAL 中停用可选功能。此属性会报告应停用的可选功能。系统的所有允许可选功能均在汽车服务叠加层中声明，即 config_allowed_optional_car_features。此属性允许停用叠加层中定义的功能。如果没有此属性，叠加层中声明的所有功能都将被启用。值 READ 应包含所有已停用的功能，并以英文逗号 (,) 分隔。例如：com.android.car.user.CarUserNoticeService,storage_monitoring

更改模式：STATIC
访问模式：READ
枚举类型：无
单位类型：无
版本：Android 13

DISPLAY_BRIGHTNESS

用于表示显示屏亮度的属性。 某些车辆只有一个用于控制所有显示屏亮度的控件。此属性用于共享对该控件的更改。如果配备了亮度受单独控制的显示屏，汽车必须使用 PER_DISPLAY_BRIGHTNESS。应仅实现 DISPLAY_BRIGHTNESS 和 PER_DISPLAY_BRIGHTNESS 中的一个。如果这两者都可用，AAOS 会使用 PER_DISPLAY_BRIGHTNESS。如果此属性可写入，Android 可以在用户通过“设置”更改显示屏亮度时设置此值。如果仅为 READ，用户仍可通过“设置”更改显示屏亮度，但更改不得反映在其他显示屏上。

更改模式：ON_CHANGE
访问模式：READ_WRITE
枚举类型：无
单位类型：无
版本：Android 13

DISTANCE_DISPLAY_UNITS

显示距离单位。 表示汽车使用哪些单位向用户显示距离。例如，英里、米或公里。距离单位在 VehicleUnit 中定义。VehiclePropConfig.configArray 用于表示支持的距离显示单位。例如，configArray[0] = METER configArray[1] = KILOMETER configArray[2] = MILE。如果更新 DISTANCE_DISPLAY_UNITS 会影响其他 *_DISPLAY_UNITS 属性的值，则必须更新它们的值，并也将其传达给 AAOS 框架。此属性定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：VehicleUnit
单位类型：无
版本：Android 13

DOOR_CHILD_LOCK_ENABLED

已启用车门童锁功能。 如果已启用车门童锁功能，则返回 true；如果已停用，则返回 false。如果已启用，门就无法从内部打开。此属性被定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 14

DOOR_LOCK

门锁为 true 表示门已上锁。此属性被定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 13

DOOR_MOVE

必须定义每个 VehicleAreaConfig 中的 maxInt32Value 和 minInt32Value。必须支持 minInt32Value 到 maxInt32Value 之间的所有整数。maxInt32Value 表示车门在打开时的最快移动速度。minInt32Value 表示车门在关闭时的最慢移动速度。

绝对值越大（无论是正值还是负值），表示移动速度就越快。门达到位置极限后，该值必须重置为 0。如果 DOOR_MOVE 的值为 0，则表示目前没有发生任何移动。

此属性不采用任何特定单位，而是采用相对移动速度的指定范围。

此属性定义为 VehiclePropertyAccess.READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 13

DOOR_POS

车门位置。 必须定义 VehicleAreaConfig 中的 maxInt32Value 和 minInt32Value。 必须支持 minInt32Value 到 maxInt32Value 之间的所有整数。minInt32Value 表示车门已关闭。minInt32Value 必须是 0。maxInt32Value 表示车门已完全打开。介于 minInt32Value 和 maxInt32Value 之间的值表示门处于关闭位置和完全打开位置之间的过渡状态。

此属性不采用任何特定单位，而是采用相对位置的指定范围。某些车辆（小型货车）可以通过电动方式打开车门。因此，具备 WRITE 此属性的能力。此属性定义为 VehiclePropertyAccess READ_WRITE，但 OEM 可以将其实现为仅 VehiclePropertyAccess.READ。

更改模式：ON_CHANGE
访问模式：READ_WRITE/READ
枚举类型：无
单位类型：无
版本：Android 13

E 到 G

ELECTRONIC_TOLL_COLLECTION_CARD_STATUS

Electronic Toll Collection card status. This property indicates the status of ETC card in this vehicle. If the head unit is aware of an ETC card attached to the vehicle, ELECTRONIC_TOLL_COLLECTION_CARD_TYPE gives that status of the card. Otherwise, this property should be UNAVAILABLE

Change mode: ON_CHANGE
Access mode: READ
Enum type: ElectronicTollCollectionCardStatus
Unit type: N/A
Release: Android 13

ELECTRONIC_TOLL_COLLECTION_CARD_TYPE

Electronic Toll Collection (ETC) card type. This property indicates the type of ETC card in this vehicle. If the head unit is aware of an ETC card attached to the vehicle, this property should return the type of card attached; otherwise, this property should be UNAVAILABLE

Change mode: ON_CHANGE
Access mode: READ
Enum type: ElectronicTollCollectionCardType
Unit type: N/A
Release: Android 13

EMERGENCY_LANE_KEEP_ASSIST_ENABLED

Enable or disable Emergency Lane Keep Assist (ELKA). Set true to enable ELKA and false to disable ELKA. When ELKA is enabled, the ADAS system in the vehicle should be on and monitoring for unsafe lane changes by the driver. When an unsafe maneuver is detected, ELKA alerts the driver and applies steering corrections to keep the vehicle in its original lane. In general, EMERGENCY_LANE_KEEP_ASSIST_ENABLED should always return true or false. If the feature is not available due to some temporary state, such as the vehicle speed being too low, that information must be conveyed through the ErrorState values in the EMERGENCY_LANE_KEEP_ASSIST_STATE property. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

EMERGENCY_LANE_KEEP_ASSIST_STATE

Emergency Lane Keep Assist (ELKA) state. Returns the current state of ELKA. Generally, this property should return a valid state defined in the EmergencyLaneKeepAssistState or ErrorState For example, if the feature is not available due to some temporary state, that information should be conveyed through ErrorState For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of EmergencyLaneKeepAssistState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: EmergencyLaneKeepAssistState/ErrorState
Unit type: N/A
Release: Android 14

ENGINE_COOLANT_TEMP

Temperature of engine coolant.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:CELSIUS
Release: Android 13

ENGINE_IDLE_AUTO_STOP_ENABLED

Represents feature for engine idle automatic stop. If true, the vehicle may automatically shut off the engine when it is not needed and then automatically restart it when needed. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

ENGINE_OIL_LEVEL

Engine oil level.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleOilLevel
Unit type: N/A
Release: Android 13

ENGINE_OIL_TEMP

Temperature of engine oil.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:CELSIUS
Release: Android 13

ENGINE_RPM

Engine revolutions per minute (RPM).

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:RPM
Release: Android 13

ENV_OUTSIDE_TEMPERATURE

Outside temperature. This property must communicate the temperature reading of the environment outside the vehicle. If there are multiple sensors for measuring the outside temperature, this property should be populated with the mean or a meaningful weighted average of the readings that best represent the temperature of the outside environment.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:CELSIUS
Release: Android 13

EV_BATTERY_DISPLAY_UNITS

EV battery units for display. Indicates which units the car is using to display EV battery information to the user. For example, watt-hours (Wh), kilowatt-hours (kWh) or ampere-hours (Ah). VehiclePropConfig.configArray is used to indicate the supported electrical energy. units. Electrical energy units are defined in VehicleUnit For example:

  configArray[0] = WATT_HOUR configArray[1] = AMPERE_HOURS configArray[2] = KILOWATT_HOUR

If updating EV_BATTERY_DISPLAY_UNITS affects the values of other *_DISPLAY_UNITS properties, then their values must be updated and communicated to the AAOS framework as well. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleUnit
Unit type: N/A
Release: Android 13

EV_BATTERY_INSTANTANEOUS_CHARGE_RATE

EV instantaneous charge rate in milliwatts. A positive value indicates the battery is being charged. A negative value indicates the battery being discharged.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MW
Release: Android 13

EV_BATTERY_LEVEL

Returns the current battery level, whether EV or hybrid. This value will not exceed EV_CURRENT_BATTERY_CAPACITY To calculate the battery percentage, use (EV_BATTERY_LEVEL, EV_CURRENT_BATTERY_CAPACITY)*100.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:WH
Release: Android 13

EV_BRAKE_REGENERATION_LEVEL

Regenerative braking level of a electronic vehicle. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All values between minInt32Value and maxInt32Value must be supported. The minInt32Value must be 0. The maxInt32Value indicates the setting for the maximum amount of energy regenerated from braking. The minInt32Value indicates the setting for no regenerative braking. This property is a more granular form of EV_REGENERATIVE_BRAKING_STATE It allows the user to set a more specific level of regenerative braking if the states in EvRegenerativeBrakingState are not granular enough for the OEM. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

EV_CHARGE_CURRENT_DRAW_LIMIT

Indicates the maximum current draw threshold for charging set by the user. EvChargeState::configArray[0] is used to specify the max current draw allowed by the vehicle in Amperes. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITEREAD
Enum type: N/A
Unit type: VehicleUnit:AMPERE
Release: Android 13

EV_CHARGE_PERCENT_LIMIT

Indicates the maximum charge percent threshold set by the user. Indicates the maximum charge percent threshold set by the user. Returns a float value from 0 to 100. configArray is used to specify the valid values. For example, if the vehicle supports the following charge percent limit values: [20, 40, 60, 80, 100] then the configArray should be {20, 40, 60, 80, 100} If the configArray is empty then all values from 0 to 100 must be valid. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE,, READ
Enum type: N/A
Unit type: N/A
Release: Android 13

EV_CHARGE_PORT_CONNECTED

EV charge port connected. If the vehicle has multiple charging ports, this property must return true when any of the charge ports are connected.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

EV_CHARGE_PORT_OPEN

EV charge port open. If the vehicle has multiple charging ports, this property must return true if any of the charge ports are open. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITEREAD
Enum type: N/A
Unit type: N/A
Release: Android 13

EV_CHARGE_STATE

Charging state of the car Returns the current charging state of the car. If the vehicle has a target charge percentage other than 100, this property must return EvChargeState::STATE_FULLY_CHARGED when the battery charge level has reached the target level. See EvChargeState::EV_CHARGE_PERCENT_LIMIT for more context.

Change mode: ON_CHANGE
Access mode: READ
Enum type: EvChargeState
Unit type: N/A
Release: Android 13

EV_CHARGE_SWITCH

Start or stop charging the EV battery. The setting wanted by the user. Setting this property to true starts the battery charging, and false to stop charging. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITEREAD
Enum type: N/A
Unit type: N/A
Release: Android 13

EV_CHARGE_TIME_REMAINING

Estimated charge time remaining in seconds. Returns 0 if the vehicle is not charging.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:SECS
Release: Android 13

EV_CURRENT_BATTERY_CAPACITY

Current usable battery capacity for and EV or hybrid vehicle. Returns the actual value of battery capacity, when EV or hybrid. This property captures the real-time usable battery capacity taking into account factors such as battery aging and temperature dependency. This value might differ from INFO_EV_BATTERY_CAPACITY because INFO_EV_BATTERY_CAPACITY returns the nominal battery capacity from when the vehicle was new.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:WH
Release: Android 14

EV_REGENERATIVE_BRAKING_STATE

Regenerative braking or one-pedal drive setting of the car. Returns the current setting associated with the regenerative braking setting in the car. If the OEM requires more setting than those provided in EvRegenerativeBrakingState, the EV_BRAKE_REGENERATION_LEVEL property can be used instead, which provides more granular information.

Change mode: ON_CHANGE
Access mode: READ
Enum type: EvRegenerativeBrakingState
Unit type: N/A
Release: Android 13

EV_STOPPING_MODE

Represents property for the current stopping mode of the vehicle. For the global area ID (0), the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of EvStoppingMode are supported. The EvStoppingMode enum may be extended to include more states in the future. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs have the option to implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: EvStoppingMode
Unit type: N/A
Release: Android 14

EVS_SERVICE_REQUEST

Enable and request an EVS service. The property provides a way to trigger EVS services. The VHAL should use this property to request Android to start or stop EVS service.

• int32Values[0] Type of EVS service. The value must be and enum in EvsServiceType.
• int32Values[1] State of the EVS service. The value must be one of enums in EvsServiceState.

For example, to enable rear view EVS service, Android can set the property value as:

[EvsServiceType::REAR_VIEW, EvsServiceState::ON]

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

EXTERNAL_CAR_TIME

Current date and time suggestion for the cr, encoded as Epoch time (in milliseconds). This value denotes the number of milliseconds seconds that have elapsed since 1/1/1970 UTC. This property signals a change in CarTime to Android. If the property is supported, VHAL must report the most accurate current CarTime when this property is read, and publish a change to this property when the CarTime value has changed.

An on-change event for this property must be published when CarTime changes for any reason other than the natural elapse of time (time delta smaller than 500ms should not trigger an on change event). Android will read and subscribe to this property to fetch time from VHAL. This can be useful to synchronize Android's time with other vehicle systems (dash clock). int64Values[0] = provided Epoch time (in milliseconds) Whenever a new Value for the property is received, AAOS creates and sends an ExternalTimeSuggestion to the TimeDetectorService.

If other sources do not have a higher priority, Android will use this to set the system time. For information on how to adjust time source priorities and how time suggestions are handled (including how Android handles gitter, drift, and minimum resolution), see the Time Detector Service documentation.

Note: The property may take more than 0ms to be propagated through the stack and having a timestamped property helps reduce any time drift. So, for all reads to the property, the timestamp can be used to negate this drift:

drift = elapsedTime - PropValue.timestamp effectiveTime = PropValue.value.int64Values[0] + drift

We strongly recommend that this propertynot be used to retrieve time from ECUs using protocols (such as GNSS, NTP, and Telephony). Since these protocols are already supported by Android, we recommend you use Android systems instead of wiring through the VHAL with this property.

Warning: The value available through this property should in no way depend on a value written by Android to the ANDROID_EPOCH_TIME property.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MILLI_SECS
Release: Android 13

FOG_LIGHTS_STATE

Fog light state. Return the current state of fog lights. If the:

• Car has front and rear fog lights. Front and rear fog lights can only be controlled together. FOG_LIGHTS_STATE must be implemented. FRONT_FOG_LIGHTS_STATE and REAR_FOG_LIGHTS_STATE must not be implemented.
• Front and rear fog lights can only be controlled independently. FOG_LIGHTS_STATE must not be implemented and FRONT_FOG_LIGHTS_STATE and REAR_FOG_LIGHTS_STATE must be implemented.
• Car has only front fog lights. Only one of FOG_LIGHTS_STATE or FRONT_FOG_LIGHTS_STATE must be implemented (not both). REAR_FOG_LIGHTS_STATE must not be implemented.
• Car has only rear fog lights. Only one of FOG_LIGHTS_STATE or REAR_FOG_LIGHTS_STATE must be implemented (not both). FRONT_FOG_LIGHTS_STATE must not be implemented.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

FOG_LIGHTS_SWITCH

Fog light switch. The setting wanted by the user. If the:

• Car has both front and rear fog lights. If front and rear fog lights can only be controlled together, FOG_LIGHTS_SWITCH must be implemented. FRONT_FOG_LIGHTS_SWITCH and REAR_FOG_LIGHTS_SWITCH must not be implemented.
• Front and rear fog lights can only be controlled independently. FOG_LIGHTS_SWITCH must not be implemented. FRONT_FOG_LIGHTS_SWITCH and REAR_FOG_LIGHTS_SWITCH must be implemented.
• Car has only front fog lights. Only one of FOG_LIGHTS_SWITCH or FRONT_FOG_LIGHTS_SWITCH must be implemented (not both). REAR_FOG_LIGHTS_SWITCH must not be implemented.
• Car has only rear fog lights. Only one of FOG_LIGHTS_SWITCH or REAR_FOG_LIGHTS_SWITCH must be implemented (and not both). FRONT_FOG_LIGHTS_SWITCH must not be implemented.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

FORWARD_COLLISION_WARNING_ENABLED

Enable or disable Forward Collision Warning (FCW). Set to true to enable FCW and false to disable FCW. When FCW is enabled, the ADAS system in the vehicle should be turned on and monitoring for potential collisions. In general, FORWARD_COLLISION_WARNING_ENABLED should always return true or false. If the feature is not available due to some temporary state, such as the vehicle speed being too low, that information must be conveyed through the ErrorState values in the FORWARD_COLLISION_WARNING_STATE property.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

FORWARD_COLLISION_WARNING_STATE

Forward Collision Warning (FCW) state. Returns the current state of FCW. This property must always return a valid state defined in ForwardCollisionWarningState or ErrorState It must not surface errors through StatusCode and must use the supported error states instead. For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both ForwardCollisionWarningState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enun type: ForwardCollisionWarningState/ErrorState
Unit type: N/A
Release: Android 14

FRONT_FOG_LIGHTS_STATE

Front fog lights state. Returns the current state of the front fog lights. Only one of FOG_LIGHTS_STATE or FRONT_FOG_LIGHTS_STATE must be implemented. Refer to the documentation on FOG_LIGHTS_STATE for more information.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

FRONT_FOG_LIGHTS_SWITCH

Front fog lights switch. The setting wanted by the user. Only one of FOG_LIGHTS_SWITCH or FRONT_FOG_LIGHTS_SWITCH must be implemented. Refer to the documentation on FOG_LIGHTS_SWITCH for more information.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

FUEL_CONSUMPTION_UNITS_DISTANCE_OVER_VOLUME

Fuel consumption units for display. Indicates type of units the car is using to display fuel consumption information to user True indicates units are distance over volume such as MPG. False indicates units are volume over distance such as L/100KM. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

FUEL_DOOR_OPEN

Fuel door open. This property must communicate if the fuel door on the vehicle is open or not. This property does not apply to EVs. That is, if INFO_FUEL_TYPE only contains FuelType::FUEL_TYPE_ELECTRIC, this property must not be implemented. For EVs, implement EV_CHARGE_PORT_OPEN. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

FUEL_LEVEL

Fuel remaining in the vehicle, in milliliters. This property must communicate the current amount of fuel remaining in the vehicle in milliliters. This property does not apply to electric vehicles. That is, if INFO_FUEL_TYPE only contains FuelType::FUEL_TYPE_ELECTRIC, this property must not be implemented. For EVs, implement EV_BATTERY_LEVEL Value can not exceed INFO_FUEL_CAPACITY

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MILLILITER
Release: Android 13

FUEL_LEVEL_LOW

Warning for fuel low level. This property corresponds to the low fuel warning on the dashboard. Once FUEL_LEVEL_LOW is set, it should not be cleared until more fuel is added to the vehicle. This property can account for all fuel sources in a vehicle. For example, in a:

• Gas-powered vehicle, this property is based solely on gas level.
• Battery powered vehicle, this property is based only on battery level.
• Hybrid vehicle, this property may can based on a combination of gas and battery levels, at the OEM's discretion.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

FUEL_VOLUME_DISPLAY_UNITS

Fuel volume units for display. Indicates which units the car is using to display fuel volume to the user. For example, Liter or Gallon. VehiclePropConfig.configArray is used to indicate the supported fuel volume display units. Volume units are defined in VehicleUnit For example, configArray[0] = LITER configArray[1] = GALLON If updating FUEL_VOLUME_DISPLAY_UNITS affects the values of other *_DISPLAY_UNITS properties, then their values must be updated and communicated to the AAOS framework, too. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleUnit
Unit type: N/A
Release: Android 13

GEAR_SELECTION

The gear selected by the user. Values in the config data must represent the list of supported gears for this vehicle. For example, config data for an automatic transmission must contain {GEAR_NEUTRAL, GEAR_REVERSE, GEAR_PARK, GEAR_DRIVE, GEAR_1, GEAR_2,...} and for manual transmission the list must be {GEAR_NEUTRAL, GEAR_REVERSE, GEAR_1, GEAR_2,...} For an automatic transmission vehicle that allows the driver to select specific gears on demand (for example, manual mode), the value for GEAR_SELECTION must be set to the specific gear selected by the driver instead of GEAR_DRIVE

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleGear
Unit type: N/A
Release: Android 13

GENERAL_SAFETY_REGULATION_COMPLIANCE_REQUIREMENT

EU's General security regulation compliance requirement. Returns a value to indicate if general security regulation compliance is required and, if so, the type of requirement.

Change mode: STATIC
Access mode: READ
Enum type: GsrComplianceRequirementType
Unit type: N/A
Release: Android 14

GLOVE_BOX_DOOR_POS

Property that represents the current position of the glove box door. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates that the glove box door is closed. The minInt32Value must be 0. The maxInt32Value indicates that the glove box door is in the fully open position. Values in between minInt32Value and maxInt32Value indicate a transition state between the closed and fully open positions.

This property is not in any particular unit but in a specified range of relative positions. The area ID must match the seat by which the glove box is intended to be used. For example if the front right dashboard has a glove box embedded in it, then the area ID should be SEAT_1_RIGHT

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

GLOVE_BOX_LOCKED

Lock or unlock the glove box. If true, the glove box is locked. If false, the glove box is unlocked. The area ID must match the seat by which the glove box is intended to be used. For example, if the front right dashboard has an embedded glove box embedded, then the area ID should be VehicleAreaSeat#ROW_1_RIGHT

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

H 到 I

HANDS_ON_DETECTION_DRIVER_STATE

Hands On Detection (HOD) driver state. Returns whether the driver's hands are on the steering wheel. Generally, this property should return a valid state defined in the HandsOnDetectionDriverState or ErrorState For example, if the feature is not available due to some temporary state, that information should be conveyed through ErrorState If the vehicle wants to send a warning to the user because the driver's hands have been off the steering wheel for too long, the warning should be surfaced through HANDS_ON_DETECTION_WARNING For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both HandsOnDetectionDriverState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: HandsOnDetectionDriverState/ErrorState
Unit type: N/A
Release: Android 14

HANDS_ON_DETECTION_ENABLED

Enable or disable Hands On Detection (HOD). Set true to enable HOD and false to disable HOD. When HOD is enabled, a system inside the vehicle should be monitoring the presence of the driver's hands on the steering wheel and send a warning if it detects that the driver's hands are no longer on the steering wheel. In general, HANDS_ON_DETECTION_ENABLED should always return true or false.

If the feature is not available due to some temporary state, that information must be conveyed through the ErrorState values in the HANDS_ON_DETECTION_STATE property. This property is defined as minInt32Value VehiclePropertyAccess.READ_WRITE, but OEMs can implement it is VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

HANDS_ON_DETECTION_WARNING

Hands On Detection (HOD) warning. Returns whether a warning is being sent to the driver for having their hands off the wheel for too long a duration. Generally, this property should return a valid state defined in HandsOnDetectionWarning or ErrorState For example, if the feature is not available due to some temporary state, that information should be conveyed through an ErrorState For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both HandsOnDetectionWarning (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: HandsOnDetectionWarning/ErrorState
Unit type: N/A
Release: Android 14

HAZARD_LIGHTS_STATE

Hazard light status. Return the current status of hazard lights.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

HAZARD_LIGHTS_SWITCH

Hazard light switch. The setting that the user wants. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

HEADLIGHTS_STATE

Headlights state. Returns the current state of headlights.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

HEADLIGHTS_SWITCH

Headlight switch. The setting that the user wants. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

HIGH_BEAM_LIGHTS_STATE

High beam lights state. Returns the current state of high beam lights.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

HIGH_BEAM_LIGHTS_SWITCH

High beam light switch. The setting that the user wants. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

HVAC_AC_ON

Turn AC on and off AC for the designated areaId. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_ACTUAL_FAN_SPEED_RPM

Actual fan speed.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_AUTO_ON

Turn automatic climate control on and off. If true, automatic climate control is on. If false, automatic climate control is off. If the vehicle does not support directly turning off automatic climate control, then OEMs should add logic in their VHAL implementation to set HVAC_AUTO_ON to false, which changes the necessary HVAC settings to indirectly turn off HVAC_AUTO_ON Ideally, this should not disrupt the user. OEMs should revert to the previous state any settings that were modified when automatic climate control is off. This way, the only outcome should be that HVAC_AUTO_ON is off. If restoring HVAC settings to previous settings is not possible, then the OEM should implement the least disruptive change.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_AUTO_RECIRC_ON

Automatic recirculation on or off. When automatic recirculation is on, the HVAC system may automatically switch to recirculation mode if the vehicle detects poor incoming air quality. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_DEFROSTER

Fan-based defrost for designated window. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_DUAL_ON

Enable temperature coupling between areas. The AreaIDs for the HVAC_DUAL_ON property shall contain a combination of HVAC_TEMPERATURE_SET AreaIDs that can be coupled together. If HVAC_TEMPERATURE_SET is mapped to AreaIDs[a_1, a_2, ..., a_n] and if HVAC_DUAL_ON can be enabled to couple a_i and a_j, then HVAC_DUAL_ON property must be mapped to [a_i | a_j]. Further, if a_k and a_l can also be coupled together separately, then HVAC_DUAL_ON must be mapped to [a_i | a_j, a_k | a_l]. For example, a car has two front seats (ROW_1_LEFT and ROW_1_RIGHT) and three back seats (ROW_2_LEFT, ROW_2_CENTER, and ROW_2_RIGHT). There are two temperature control units, driver side and passenger side, which can be optionally synchronized. This can be expressed this way in the AreaIDs:

HVAC_TEMPERATURE_SET > [ROW_1_LEFT | ROW_2_LEFT, ROW_1_RIGHT | ROW_2_CENTER | ROW_2_RIGHT]
HVAC_DUAL_ON > [ROW_1_LEFT | ROW_2_LEFT | ROW_1_RIGHT | ROW_2_CENTER | ROW_2_RIGHT]

When the property is enabled, the ECU must synchronize the temperature for the affected areas. Any parameters modified as a side effect of turning on or off the DUAL_ON parameter shall generate onPropertyEvent() callbacks to the VHAL. In addition, if setting a temperature (for example, driver temperature) changes another temperature (such as front passenger temperature), then the appropriate onPropertyEvent() callbacks must be generated.

If a user changes a temperature that breaks the coupling (for example, sets passenger temperature independently), then the VHAL must send the appropriate onPropertyEvent() callbacks (including HVAC_DUAL_ON = false and HVAC_TEMPERATURE_SET[AreaID] = xxx). This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_ELECTRIC_DEFROSTER_ON

Electric defrosters' status.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_FAN_DIRECTION

Fan direction setting. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleHvacFanDirection
Unit type: N/A
Release: Android 13

HVAC_FAN_DIRECTION_AVAILABLE

Fan positions available. This is a bit mask of fan positions available for the zone. Each available fan direction is denoted by a separate entry in the vector. A fan direction can have multiple bits from vehicle_hvac_fan_direction set. For instance, a typical car may have these fan positions:

- FAN_DIRECTION_FACE (0x1) - FAN_DIRECTION_FLOOR (0x2) - FAN_DIRECTION_FACE | FAN_DIRECTION_FLOOR (0x3) - FAN_DIRECTION_DEFROST (0x4) - FAN_DIRECTION_FLOOR | FAN_DIRECTION_DEFROST (0x6)

Change mode: STATIC
Access mode: READ
Enum type: VehicleHvacFanDirection
Unit type: N/A
Release: Android 13

HVAC_FAN_SPEED

Fan speed setting. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

• minInt32Value lowest fan speed
• maxInt32Value highest fan speed

This property is not in any specific unit but in a specified range of relative speeds. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can elect to implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_MAX_AC_ON

MAX AC on or off. When MAX AC is on, the ECU can adjust items such as vent position, fan speed, and temperature as needed to cool the vehicle as quickly as possible. Any parameters modified as a side effect of turning on or off the MAX AC parameter generates onPropertyEvent() callbacks to the VHAL. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_MAX_DEFROST_ON

Turn MAX DEFROST on and off. When MAX DEFROST is on, the ECU can adjust items such as vent position, fan speed, and temperature as needed to defrost the windows as quickly as possible. Any parameters modified as a side effect of turning on or off MAX DEFROST parameter generates onPropertyEvent() callbacks to the VHAL. The AreaIDs for HVAC_MAX_DEFROST_ON indicate MAX DEFROST can be controlled in the area. For example, areaConfig.areaId = {ROW_1_LEFT | ROW_1_RIGHT} indicates that HVAC_MAX_DEFROST_ON can only be controlled for the front rows. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_POWER_ON

Represents the global power state for HVAC. Setting this property to false MAY mark some properties that control individual HVAC features and subsystems in the UNAVAILABLE state. Setting this property to true MAY mark some properties that control individual HVAC features and subsystems to the AVAILABLE state (unless any or all of the properties are UNAVAILABLE on their own individual merits).

HvacPower_DependentProperties are those properties that require HVAC to be powered on to enable functionality. In some cars, for example, to turn on the AC, HVAC must first be powered on. The HvacPower_DependentProperties list must be set in the VehiclePropConfig.configArray HvacPower_DependentProperties must only contain those properties associated with VehicleArea:SEAT

Note: Properties not associated with VehicleArea:SEAT (for example, HVAC_DEFROSTER) must never depend on the HVAC_POWER_ON property and must never belong to the HvacPower_DependentPropertieslist.

AreaID mapping for HVAC_POWER_ON property must contain all AreaIDs that HvacPower_DependentProperties are mapped to. For example, a car has two:

1. Front seats (ROW_1_LEFT, ROW_1_RIGHT) and three back seats (ROW_2_LEFT, ROW_2_CENTER, ROW_2_RIGHT). If the HVAC features (AC, Temperature etc.) throughout the car are dependent on a single HVAC power controller, then HVAC_POWER_ON must be mapped to [ROW_1_LEFT | ROW_1_RIGHT | ROW_2_LEFT | ROW_2_CENTER | ROW_2_RIGHT]
2. Seats in the front row (ROW_1_LEFT, ROW_1_RIGHT) and three seat in the second (ROW_2_LEFT, ROW_2_CENTER, ROW_2_RIGHT) and third rows (ROW_3_LEFT, ROW_3_CENTER, ROW_3_RIGHT). If the car has temperature controllers in the front row that can operate entirely independently of temperature controllers in the back of the vehicle, then HVAC_POWER_ON must be mapped to a two element array:

   - ROW_1_LEFT | ROW_1_RIGHT - ROW_2_LEFT | ROW_2_CENTER | ROW_2_RIGHT | ROW_3_LEFT | ROW_3_CENTER | ROW_3_RIGHT
   

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs have the option to implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_RECIRC_ON

Recirculation on and off. Controls the supply of exterior air to the cabin. Recirc on means most of the airflow into the cabin originates in the cabin. Recirc off means most of the airflow into the cabin comes from outside the car. This property is defined as VehiclePropertyAccess.READ_WRITE but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_SEAT_TEMPERATURE

Seat heating and cooling. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the maximum seat temperature heating setting. The minInt32Value must be 0, unless the vehicle supports seat cooling. In this case, minInt32Value indicates the maximum seat temperature cooling setting. This property is not in any specific unit, but in a specified range of relative temperature settings. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_SEAT_VENTILATION

Seat ventilation. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value must be 0. The maxInt32Value indicates the maximum ventilation setting available for the seat.

This property is not in any particular unit but in the specified range of ventilation settings.

Used by HVAC apps and Assistant to enable, change, or read state of seat ventilation. This is different than seating cooling. It can be on at the same time as cooling, or not.

This property is defined as >VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_SIDE_MIRROR_HEAT

Side mirror heat. Increasing values denote higher heating levels for side mirrors. You must define maxInt32Value and minInt32Value in VehicleAreaConfig All integers between minInt32Value and maxInt32Value must be supported. In config data:

• maxInt32Value represents maximum heating level.
• minInt32Value MUST be 0 and indicates no heating.

This property is not in any particular unit but in a specified range of relative heating settings. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs have the option to implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_STEERING_WHEEL_HEAT

Sets the amount of heating and cooling for the steering wheel. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the maximum steering wheel heating setting. The minInt32Value should be 0, unless the vehicle supports steering wheel cooling, too. In this case, the minInt32Value indicates the maximum steering wheel cooling setting. This property is not in any particular unit but in a specified range of heating settings. This property is defined as VehiclePropertyAccess.READ, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HVAC_TEMPERATURE_CURRENT

HVAC current temperature.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:CELSIUS
Release: Android 13

HVAC_TEMPERATURE_DISPLAY_UNITS

Temperature units for display. Indicates if temperature is displayed in Celsius or Fahrenheit. VehiclePropConfig.configArray indicates the supported temperature display units. For example, configArray[0] = CELSIUS configArray[1] = FAHRENHEIT This parameter MAY be used to display any HVAC temperature in the system. Values must be one of VehicleUnit.CELSIUS or VehicleUnit.FAHRENHEIT

Note:Internally, all temperatures are represented in floating point Celsius.

If updating HVAC_TEMPERATURE_DISPLAY_UNITS affects the values of other *_DISPLAY_UNITSproperties, then their values must be updated and communicated to the AAOS framework.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it is VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleUnit
Unit type: N/A
Release: Android 13

HVAC_TEMPERATURE_SET

HVAC target temperature set in Celsius.

The minFloatValue and maxFloatValue in VehicleAreaConfig must be defined:

• minFloatValue minimum temperature setting in Celsius.
• maxFloatValue maximum temperature setting in Celsius.

If all the values between minFloatValue and maxFloatValue are not supported, use the configArray to list the valid temperature values that can be set. This also describes a lookup table to convert the temperature from Celsius to Fahrenheit (and vice versa) for the vehicle. The configArray must be defined if standard unit conversion is not supported on the vehicle.

The configArray is set as follows:

• configArray[0] [lower bound of supported temperature in Celsius] * 10
• configArray[1] [upper bound of supported temperature in Celsius] * 10
• configArray[2] [increment in Celsius] * 10
• configArray[3] [lower bound of the supported temperature in Fahrenheit] * 10
• configArray[4] [upper bound of the supported temperature in Fahrenheit] * 10
• configArray[5] [increment in Fahrenheit] * 10

The minFloatValue and maxFloatValue in VehicleAreaConfig must be equal to configArray[0] and configArray[1] respectively. For example, if the vehicle supports temperature values as [16.0, 16.5, 17.0 ,..., 28.0] in Celsius [60.5, 61.5, 62.5 ,..., 84.5] in Fahrenheit, the configArray should be configArray = {160, 280, 5, 605, 845, 10}

Ideally, the ratio of the Celsius increment to the Fahrenheit increment should be as close to the actual ratio of 1 degree Celsius to 1.8 degrees Fahrenheit. There must be a one-to-one mapping of all Celsius values to Fahrenheit values defined by the configArray The configArray is used by clients to convert this property's temperature from Celsius to Fahrenheit. Also, it lets clients know what Celsius value to set the property to achieve their desired Fahreneheit value for the system. If the ECU does not have a one-to-one mapping of all Celsius values to Fahrenheit values, then the configArray should only define the list of Celsius and Fahrenheit values that have a one-to-one mapping.

For example, if the ECU supports Celsius values from 16 to 28 and Fahrenheit values from 60 to 85, each with an increment of 1, then one possible configArray is code>{160, 280, 10, 600, 840, 20}In this case, 85 is not a supported temperature.

Any value set in between a valid value should be rounded to the closest valid value. We highly recommended that the OEM also implement the HVAC_TEMPERATURE_VALUE_SUGGESTION vehicle property because it provides applications with a simple method for determining temperature values that can be set for a vehicle and for converting values between Celsius and Fahrenheit.

This property is defined as VehiclePropertyAccess.READ, but OEMs can implement it as VehiclePropertyAccess.READ

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: VehicleUnit:CELSIUS
Release: Android 13

HVAC_TEMPERATURE_VALUE_SUGGESTION

Suggested values for setting HVAC temperature.

Implement the property to help applications understand the closest supported temperature value in Celsius or Fahrenheit.

• floatValues[0] Requested value that an app wants to set a temperature to.
• floatValues[1] Unit for floatValues[0] and should be one of {VehicleUnit.CELSIUS, VehicleUnit.FAHRENHEIT}
• floatValues[2] Value OEMs suggested in CELSIUS (this value is not included in the request).
• floatValues[3] Value OEMs suggested in FAHRENHEIT (this value is not included in the request).

An application calls set(VehiclePropValue propValue) with the requested value and unit for the value. OEMs need to return the suggested values in floatValues[2] and floatValues[3] by onPropertyEvent() callbacks. The suggested values must conform to the values that can be derived from the HVAC_TEMPERATURE_SET configArray In other words, the suggested values and the table of values from the configArray should be the same.

We recommended that the OEM add custom logic in their VHAL implementation to avoid making requests to the HVAC ECU. The logic can be as follows. To convert temperature from Celsius to Fahrenheit:

// Given tempC and the configArray float minTempC = configArray[0] / 10.0; float temperatureIncrementCelsius = configArray[2] / 10.0; float minTempF = configArray[3] / 10.0; float temperatureIncrementFahrenheit = configArray[5] / 10.0; // Round to the closest increment int numIncrements = round((tempC - minTempC) / temperatureIncrementCelsius); tempF = temperatureIncrementFahrenheit * numIncrements + minTempF;

For example, when a driver uses the voice assistant to set HVAC temperature to 66.2 in Fahrenheit. First, an application sets this property with the value [66.2, (float)VehicleUnit.FAHRENHEIT,0,0] If an OEM suggests to set 19.0 in Celsius or 66.5 in Fahrenheit at the user's request, then VHAL must generate a callback with a property value [66.2, (float)VehicleUnit.FAHRENHEIT, 19.0, 66.5] After the voice assistant gets the callback, it informs the user and sets the HVAC temperature to the suggested value.

Another example, an app receives 21 Celsius as the current temperature value by querying HVC_TEMPERATURE_SET but the app needs to know what value is displayed on the car's UI in Fahrenheit. For this, the app sets the property to [21, (float)VehicleUnit.CELSIUS, 0, 0] If the suggested value by the OEM for 21 Celsius is 70 Fahrenheit, then VHAL must generate a callback with property value [21, (float)VehicleUnit.CELSIUS, 21.0, 70.0] In this case, the app can know that the value is 70.0 Fahrenheit in the car's UI.

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

HW_CUSTOM_INPUT

Defines a custom OEM partner input event. This input event must be used by OEM partners who want to propagate events not supported by Android. It is composed by an array of int32 values only. The Android properties are:

• int32Values[0] Input code identifying the function representing this event. Valid event types are defined by CustomInputType.CUSTOM_EVENT_F1 up to CustomInputType.CUSTOM_EVENT_F10 They represent the custom event to be defined by OEM partners.
• int32Values[1] Target display type defined in VehicleDisplay Events not tied to a specific display must be sent to VehicleDisplay#MAIN
• int32Values[2] Repeat counter, if 0 then event is not repeated. Values 1 or higher indicate how many times this event has been repeated.

Change mode: ON_CHANGE
Access mode: READ
Enum type: CustomInputType
Unit type: N/A
Release: Android 13

HW_KEY_INPUT

Property to feed hardware input events to Android.

• int32Values[0] Action defined by VehicleHwKeyInputAction
• int32Values[1] Key code, must use standard android key code
• int32Values[2] Target display defined in VehicleDisplay Events not tied to specific display must be sent to VehicleDisplay#MAIN
• int32Values[3] (Optional) Number of ticks. The value must be equal o greater than 1. When omitted, Android defaults to 1.

Change mode: .ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

HW_KEY_INPUT_V2

Property to feed hardware input events to Android.

• int32array[0] Target display defined by VehicleDisplay such as:
  VehicleDisplay::MAIN, VehicleDisplay::INSTRUMENT_CLUSTER, VehicleDisplay::AUX
• int32array[1] Key code, must use the standard Android key code, such as KEYCODE_HOME and KEYCODE_BACK
• int32array[2] action defined in VehicleHwKeyInputAction, such as:
  VehicleHwKeyInputAction::ACTION_UP, VehicleHwKeyInputAction::ACTION_UP
• int32array[3] Repeat count of the event. For key down events, this is the repeat count with the first down starting at 0 and counting up from there. For key up events, this is always equal to 0.
• int64array[0] Down time in elapsed nanoseconds since the last boot. Denotes the time of the most recent key down event. For the down event, this is the event time of the down event.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 14

HW_MOTION_INPUT

Property to feed hardware input events to Android.

• int32array[0] Target display defined by VehicleDisplay, such as:
  VehicleDisplay::MAIN, VehicleDisplay::INSTRUMENT_CLUSTER, VehicleDisplay::AUX
• int32array[1] Input type defined in VehicleHwMotionInputSource, such as:
  VehicleHwMotionInputSource::SOURCE_KEYBOARD, VehicleHwMotionInputSource::SOURCE_DPAD
• int32array[2] Action code defined in VehicleHwMotionInputAction, such as:
  VehicleHwMotionInputAction::ACTION_UP, VehicleHwMotionInputAction::ACTION_DOWN
• int32array[3] Button state flag defined in VehicleHwMotionButtonStateFlag, such as:
  VehicleHwMotionButtonStateFlag::BUTTON_PRIMARY, VehicleHwMotionButtonStateFlag::BUTTON_SECONDARY
• int32array[4] Pointer events count, N. N must be a positive integer.
• int32array[5:5+N-1] Pointer id, length N
• int32array[5+N:5+2*N-1] Tool type, length N. As defined in VehicleHwMotionToolType, such as:
  VehicleHwMotionToolType::TOOL_TYPE_FINGER, VehicleHwMotionToolType::TOOL_TYPE_STYLUS
• floatArray[0:N-1] x data, length N
• floatArray[N:2*N-1] y data, length N
• floatArray[2*N:3*N-1] pressure data, length N
• floatArray[3*N:4*N-1] size data, length N
• int64array[0] Down time, elapsed nanoseconds since boot. Denotes the time when the user originally pressed down to start a stream of position events. For the down event, it is the event time of the down event.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 14

HW_ROTARY_INPUT

Property to feed hardware rotary events to Android.

• int32Values[0] RotaryInputType to identify which rotary knob is rotated.
• int32Values[1] Number of detents (clicks), positive for clockwise, negative for counterclockwise.
• int32Values[2] Target display defined in VehicleDisplay Events not tied to a specific display must be sent to VehicleDisplay#MAIN
• int32values[3 .. 3 + abs(number of detents) - 2] Nanosecond deltas between pairs of consecutive detents when the number of detents is more than 1 or less than -1.
• VehiclePropValue.timestamp When the rotation took place. If the number of detents is more than 1 or less than -1, when the first detent of rotation took place.

Change mode: ON_CHANGE
Access mode: READ
Enum type: RotaryInputType
Unit type: N/A
Release: Android 13

IGNITION_STATE

Represents ignition state.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleIgnitionState
Unit type: N/A
Release: Android 13

INFO_DRIVER_SEAT

Driver's seat location VHAL implementations must ignore the areaId. Use VehicleArea:GLOBAL

Change mode: STATIC
Access mode: READ
Enum type: VehicleAreaSeat
Unit type: N/A
Release: Android 13

INFO_EV_BATTERY_CAPACITY

Nominal battery capacity for EV or hybrid vehicle. Returns the nominal battery capacity, EV or hybrid. This is the total usable battery capacity when the vehicle is new. This value may differ from EV_CURRENT_BATTERY_CAPACITY because EV_CURRENT_BATTERY_CAPACITY returns the real-time usable battery capacity taking into account factors such as battery aging and temperature dependency.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:WH
Release: Android 13

INFO_EV_CONNECTOR_TYPE

List of connectors this EV may use. If the vehicle has multiple charging ports, this property must return all possible connector types that can be used by at least one charging port on the vehicle.

Change mode: STATIC
Access mode: READ
Enum type: EvConnectorType
Unit type: N/A
Release: Android 13

INFO_EV_PORT_LOCATION

This property must communicate the location of the charging port on the EV using the PortLocationType enum. If a vehicle has multiple ports, this property must return the port that allows the fastest charging. To communicate all port locations, use INFO_MULTI_EV_PORT_LOCATIONS

EV port location: STATIC
Access mode: READ
Enum type: PortLocationType
Unit type: N/A
Release: Android 13

INFO_EXTERIOR_DIMENSIONS

Exterior dimensions of vehicle:

• Height: int32Values[0]
• Length: int32Values[1]
• Width: int32Values[2]
• Width, including mirrors: int32Values[3]
• Wheel base, including mirrors: int32Values[4]
• Track width front: int32Values[5]
• Track width rear: int32Values[6]
• Curb-to-curb turning diameter: int32Values[7]

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MILLIMETER
Release: Android 13

INFO_FUEL_CAPACITY

Fuel capacity of the vehicle in milliliters. This property must communicate the maximum amount of fuel that can be stored in the vehicle in milliliters. This property does not apply to electric vehicles (EV). That is, if INFO_FUEL_TYPE only contains FuelType::FUEL_TYPE_ELECTRIC, INFO_FUEL_CAPACITY must not be implemented. For EVs, implement INFO_EV_BATTERY_CAPACITY.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MILLILITER
Release: Android 13

INFO_FUEL_DOOR_LOCATION

Fuel door location. This property must communicate the location of the fuel door on the vehicle. This property does not apply to EVs. That is, if INFO_FUEL_TYPE only contains FuelType::FUEL_TYPE_ELECTRIC, this property must not be implemented. For EVs, implement INFO_EV_PORT_LOCATION or INFO_MULTI_LOCATIONS

Change mode: STATIC
Access mode: READ
Enum type: PortLocationType
Unit type: N/A
Release: Android 13

INFO_FUEL_TYPE

List of fuels the vehicle may use. FuelType::FUEL_TYPE_ELECTRIC must only be included if the vehicle can plug-in rechargeable. For example, a Fully Hybrid Electric Vehicle (FHEV) must not include FuelType::FUEL_TYPE_ELECTRIC as the INT32_VEC value for INFO_FUEL_TYPE INFO_FUEL_TYPE can be populated as such.

int32Values = { FuelType::FUEL_TYPE_UNLEADED }

On the other hand, a Plug-in Hybrid Electric Vehicle (PHEV) is plug-in rechargeable and should include FuelType::FUEL_TYPE_ELECTRIC as the INT32_VEC value for INFO_FUEL_TYPE INFO_FUEL_TYPE can be populated as such, int32Values = { FuelType::FUEL_TYPE_UNLEADED, FuelType::FUEL_TYPE_ELECTRIC }

Change mode: STATIC
Access mode: READ
Enum type: FuelType
Unit type: N/A
Release: Android 13

INFO_MAKE

Manufacturer of vehicle. This property must communicate the vehicle's public brand name.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

INFO_MODEL

Model of vehicle. This property must communicate the vehicle's public model name.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

INFO_MODEL_YEAR

Model year of vehicle in `YYYY` format based on the Gregorian calendar.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:YEAR
Release: Android 13

INFO_MULTI_EV_PORT_LOCATIONS

Multiple EV port locations. Implement this property if the vehicle has multiple EV ports. Port locations are defined in PortLocationType. For example, a car has one port front left and one port rear left:

int32Values[0] = PortLocationType::FRONT_LEFT int32Values[1] = PortLocationType::REAR_LEFT

If a vehicle has only one port, this property's value should list one element. To describe one port location, see INFO-EV-PORT-LOCATION

.

Change mode: STATIC
Access mode: READ
Enum type: PortLocationType
Unit type: N/A
Release: Android 13

INFO_VIN

VIN of vehicle.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

INITIAL_USER_INFO

Defines the Android user to be used during initialization. This property is called by the Android system when it initializes and lets the HAL define which Android user should be started. This request is made by setting a VehiclePropValue (defined by InitialUserInfoRequest), and the HAL must respond with a property change event (defined by InitialUserInfoResponse). If the HAL doesn't respond after a time defined by the Android system, the Android system proceeds as if HAL returned a response of action InitialUserInfoResponseAction:DEFAULT. For example, on first boot, the request could be:

int32[0] 42  // request id (arbitrary number set by Android system)
int32[1] 1   // InitialUserInfoRequestType::FIRST_BOOT
int32[2] 0   // id of current user (usersInfo.currentUser.userId)
int32[3] 1   // flag of current user (usersInfo.currentUser.flags = SYSTEM)
int32[4] 1   // number of existing users (usersInfo.numberUsers);
int32[5] 0   // user #0  (usersInfo.existingUsers[0].userId)
int32[6] 1   // flags of user #0  (usersInfo.existingUsers[0].flags)

If the HAL responds with the creation of an admin user called Owner, the response would be:

int32[0] 42  // must match the request id from the request
int32[1] 2   // action = InitialUserInfoResponseAction::CREATE
int32[2] -10000  // userToSwitchOrCreate.userId (not used as user will be created)
int32[3] 8   // userToSwitchOrCreate.flags = ADMIN string: "||Owner" // userLocales + separator + userNameToCreate

The string value represents multiple values, separated by ||. The first value is the (optional) system locales for the user to be created (empty in this case meaning it uses the Android default value), while the second value is the (optional) name of the user to be created (when the type of response is InitialUserInfoResponseAction:CREATE). For example, to create the same Owner user with en-US and pt-BR locales, the string value of the response is en-US,pt-BR||Owner. As such, neither the locale nor the name can contain two vertical bars (||) in their values, although you can use a single vertical bar (|).

Note:: If the HAL doesn't support user management, then it should not define this property, which disables other user-related properties. For example, the Android system would never issue them and user-related requests from the HAL layer would be ignored by the Android system. However, if it supports user management, then it must support all core user-related properties, including INITIAL_USER_INFO, SWITCH_USER, CREATE_USER, and REMOVE_USER

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

J 到 R

LANE_CENTERING_ASSIST_COMMAND

Lane Centering Assist (LCA) commands. Commands to activate and suspend LCA. When the command ACTIVATE from LaneCenteringAssistCommand is sent, LANE_CENTERING_ASSIST_STATE must be set to LaneCenteringAssistState#ACTIVATION_REQUESTED When the ACTIVATE command succeeds, LANE_CENTERING_ASSIST_STATE must be set to LaneCenteringAssistState#ACTIVATED When the command DEACTIVATE from LaneCenteringAssistCommand succeeds, LANE_CENTERING_ASSIST_STATE must be set to LaneCenteringAssistState#ENABLED

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of LaneCenteringAssistCommand are supported. When this property is not available because LCA is disabled (for example, LANE_CENTERING_ASSIST_ENABLED is false), this property must return StatusCode#NOT_AVAILABLE_DISABLED If LANE_CENTERING_ASSIST_STATE is implemented and the state is set to an ErrorState value, then this property must return a StatusCode that aligns with the ErrorState value. For example, if LANE_CENTERING_ASSIST_STATE is set to ErrorState#NOT_AVAILABLE_SPEED_LOW then this property must return StatusCode#NOT_AVAILABLE_SPEED_LOW

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: LaneCenteringAssistCommand
Unit type: N/A
Release: Android 14

LANE_CENTERING_ASSIST_ENABLED

Enable or disable Lane Centering Assist (LCA). Set true to enable LCA and false to disable LCA. When LCA is enabled, the ADAS system in the vehicle should be turned on and waiting for an activation signal from the driver. Once the feature is activated, the ADAS system should be steering the vehicle to keep it centered in its current lane.

This is different from Lane Keep Assist (LKA) which monitors if the driver unintentionally drifts toward or over the lane marking. If an unintentional lane departure is detected, the system applies steering control to return the vehicle into the current lane. In general, LANE_CENTERING_ASSIST_ENABLED should always return true or false. If the feature is not available due to some temporary state, such as the vehicle speed being too low or too high, that information must be conveyed through the ErrorState values in the LANE_CENTERING_ASSIST_STATE property.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

LANE_CENTERING_ASSIST_STATE

Lane Centering Assist (LCA) state. Returns the current state of LCA. This property must always return a valid state defined in LaneCenteringAssistState or ErrorState It must not surface errors through StatusCode and must use the supported error states instead.

If LCA includes lane departure warnings, those warnings must be surfaced through the Lane Departure Warning (LDW) properties.

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both LaneCenteringAssistState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: LaneCenteringAssistState/ErrorState
Unit type: N/A
Release: Android 14

LANE_DEPARTURE_WARNING_ENABLED

Enable or disable Lane Departure Warning (LDW). Set true to enable LDW and false to disable LDW. When LDW is enabled, the ADAS system in the vehicle should be turned on and monitoring if the vehicle is approaching or crossing lane lines, in which case a warning will be given.

In general, LANE_DEPARTURE_WARNING_ENABLED should always return true or false. If the feature is not available due to some temporary state, such as the vehicle speed being too low or too high, that information must be conveyed through the ErrorState values in the LANE_DEPARTURE_WARNING_STATE property.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

LANE_DEPARTURE_WARNING_STATE

Lane Departure Warning (LDW) state. Returns the current state of LDW. This property must always return a valid state defined in LaneDepartureWarningState or ErrorState It must not surface errors through StatusCode and must use the supported error states instead.

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both LaneDepartureWarningState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: LaneDepartureWarningState/ErrorState
Unit type: N/A
Release: Android 14

LANE_KEEP_ASSIST_ENABLED

Enable or disable Lane Keep Assist (LKA). Set true to enable LKA and false to disable LKA. When LKA is enabled, the ADAS system in the vehicle should be turned on and monitoring if the driver unintentionally drifts toward or over the lane marking. If an unintentional lane departure is detected, the system applies steering control to return the vehicle into the current lane. This is different from Lane Centering Assist (LCA) which, when activated, applies continuous steering control to keep the vehicle centered in the current lane.

In general, LANE_KEEP_ASSIST_ENABLED should always return true or false. If the feature is not available due to some temporary state, such as the vehicle speed being too low or too high, that information must be conveyed through the ErrorState values in the LANE_KEEP_ASSIST_STATE property.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

LANE_KEEP_ASSIST_STATE

Lane Keep Assist (LKA) state. Returns the current state of LKA. This property must always return a valid state defined in LaneKeepAssistState or ErrorState It must not surface errors through StatusCode and must use the supported error states instead

If LKA includes lane departure warnings before applying steering corrections, those warnings must be surfaced through the Lane Departure Warning (LDW) properties.

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues array must be defined unless all states of both LaneKeepAssistState (including OTHER, which is not recommended) and ErrorState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: LaneKeepAssistState/ErrorState
Unit type: N/A
Release: Android 14

LOCATION_CHARACTERIZATION

Characterization of inputs used for computing location. This property must indicate what (if any) data and sensor inputs are considered by the system when computing the vehicle's location that is shared with Android through the GNSS HAL.

The value must return a collection of bit flags. The bit flags are defined in LocationCharacterization. The value must also include exactly one of DEAD_RECKONED or RAW_GNSS_ONLY among its collection of bit flags.

When this property is not supported, it is assumed that no additional sensor inputs are fused into the GNSS updates provided through the GNSS HAL. That is unless otherwise specified through the GNSS HAL interfaces.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 14

MIRROR_AUTO_FOLD_ENABLED

Represents property for Mirror Auto Fold feature. This property is true when the feature for automatically folding the vehicle's side mirrors (for example, when the mirrors fold inward automatically when one exits and locks the vehicle) is enabled.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

MIRROR_AUTO_TILT_ENABLED

Represents property for Mirror Auto Tilt feature. This property is true when the feature for automatically tilting the vehicle's side mirrors (for example, when the mirrors tilt downward automatically when one reverses the vehicle) is enabled.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

MIRROR_FOLD

Mirror fold. True indicates mirrors are folded. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

MIRROR_LOCK

Mirror lock. True indicates mirror positions are locked and not changeable. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

MIRROR_Y_MOVE

Mirror Y move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the mirror while tilting right. The minInt32Value represents the maximum movement speed of the mirror while tilting left.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the mirror reaches the positional limit, the value must reset to 0. If MIRROR_Y_MOVE's value is currently 0, then that means there is no movement currently occurring.

This property is not in any particular unit but in a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

MIRROR_Y_POS

Mirror Y position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the mirror is tilted completely to the left.

This must be a non-positive value. The maxInt32Value indicates the mirror is tilted completely to the right. This must be a non-negative value. 0 indicates the mirror is not tilted in either direction.

Values in between minInt32Value and maxInt32Value indicate a transition state between the left extreme and right extreme positions.

This property is not in any particular unit but in a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

MIRROR_Z_MOVE

Mirror Z move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the mirror while tilting upwards. The minInt32Value represents the maximum movement speed of the mirror while tilting downwards. Larger absolute values, either positive or negative, indicate a faster movement speed. Once the mirror reaches the positional limit, the value must reset to 0. If MIRROR_Z_MOVE's value is currently 0, then that means there is no movement currently occurring.

This property is not in any particular unit but in a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

MIRROR_Z_POS

Mirror Z position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the mirror is tilted completely downwards. This must be a non-positive value. The maxInt32Value indicates the mirror is tilted completely upwards. This must be a non-negative value. 0 indicates the mirror is not tilted in either direction.

Values in between minInt32Value and maxInt32Value indicate a transition state between the fully downward and fully upwards positions.

This property is not in any particular unit but in a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

NIGHT_MODE

True indicates that the night mode sensor has detected the car cabin environment to have low light. The platform can use this to, for example, enable an appropriate UI for better viewing in dark or low light environments.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

OBD2_FREEZE_FRAME

Reports a snapshot of the value of the OBD2 sensors available at the time that a fault occurred and was detected. A configArray must be provided with the same meaning as defined for OBD2_LIVE_FRAME

The values of this property are to be interpreted in a similar fashion as those for OBD2_LIVE_FRAME, with the exception that the stringValue field may contain a non-empty diagnostic troubleshooting code (DTC).

An IVehicle#get request of this property must provide a value for int64Values[0]. This is interpreted as the timestamp of the freeze frame to retrieve. A list of timestamps can be obtained by an IVehicle#get of OBD2_FREEZE_FRAME_INFO

Should no freeze frame be available at the given timestamp, a response of NOT_AVAILABLE must be returned by the implementation. Because vehicles may have limited storage for freeze frames, it is possible for a frame request to respond with NOT_AVAILABLE even if the associated timestamp has been recently obtained through OBD2_FREEZE_FRAME_INFO

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

OBD2_FREEZE_FRAME_CLEAR

Freeze frame clear. Reports a snapshot of the value of the OBD2 sensors available at the time that a fault occurred and was detected. A configArray must be provided with the same meaning as defined for OBD2_LIVE_FRAME

The values of this property are to be interpreted in a similar fashion as those for OBD2_LIVE_FRAME, with the exception that the stringValue field may contain a non-empty diagnostic troubleshooting code (DTC).

A IVehicle#get request of this property must provide a value for int64Values[0]. This will be interpreted as the timestamp of the freeze frame to retrieve. A list of timestamps can be obtained by a IVehicle#get of OBD2_FREEZE_FRAME_INFO

Should no freeze frame be available at the given timestamp, a response of NOT_AVAILABLE must be returned by the implementation. Because vehicles may have limited storage for freeze frames, it is possible for a frame request to respond with NOT_AVAILABLE even if the associated timestamp has been recently obtained via OBD2_FREEZE_FRAME_INFO

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

OBD2_FREEZE_FRAME_INFO

This property describes the current freeze frames stored in vehicle memory and available for retrieval through OBD2_FREEZE_FRAME The values are to be interpreted as follows. Each element of int64Values must be the timestamp at which a a fault code has been detected and the corresponding freeze frame stored, and each such element can be used as the key to OBD2_FREEZE_FRAME to retrieve the corresponding freeze frame.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

OBD2_LIVE_FRAME

Reports a snapshot of the current (live) values of the OBD2 sensors available. The configArray is set as follows:

• configArray[0] Number of vendor-specific integer-valued sensors
• configArray[1] Number of vendor-specific float-valued sensors

The values of this property are to be interpreted as in the following example. Considering a configArray = {2,3} int32Values must be a vector containing Obd2IntegerSensorIndex.LAST_SYSTEM_INDEX plus two elements (or, 33 elements). floatValues must be a vector containing Obd2FloatSensorIndex.LAST_SYSTEM_INDEX plus three elements (or, 73 elements).

It is possible for each frame to contain a different subset of sensor values, both system provided sensors, and vendor-specific ones. In order to support this, the bytes element of the property value is used as a bitmask. Bytes must have a sufficient number of bytes to represent the total number of possible sensors (in this case, 14 bytes to represent 106 possible values). It'is to be read as a contiguous bitmask such that each bit indicates the presence or absence of a sensor from the frame, starting with as many bits as the size of int32Values, immediately followed by as many bits as the size of floatValues.

For example, should bytes[0] = 0x4C (0b01001100) it means that:

• int32Values[0 and 1] are not valid sensor values
• int32Values[2 and 3] are valid sensor values
• int32Values[4 and 5] are not valid sensor values
• int32Values[6] is a valid sensor value
• int32Values[7] is not a valid sensor value
• int32Values[0 and 1] are not valid sensor values
• int32Values[2 and 3] are valid sensor values
• int32Values[4 and 5] are not valid sensor values
• int32Values[6] is a valid sensor value
• int32Values[7] is not a valid sensor value

If bytes[5] = 0x61 (0b01100001), then:

• int32Values[32] is a valid sensor value
• floatValues[0 thru 3] are invalid sensor values
• floatValues[4 and 5] are valid sensor values
• floatValues[6] is not a valid sensor value.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

ON_CHANGE

Change mode:
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type:N/A
Release: Android 13

PARKING_BRAKE_AUTO_APPLY

Auto-apply parking brake. When true, this property indicates that the car's automatic parking brake is enabled. False indicates that the car's automatic parking brake feature is disabled. This property is often confused with PARKING_BRAKE_ON The difference being that PARKING_BRAKE_ON indicates if the actual parking brake is on or off whereas PARKING_BRAKE_AUTO_APPLY indicates if the automatic parking brake feature is enabled or disabled and does not describe the current state of the actual parking brake.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

PARKING_BRAKE_ON

Parking brake state. When true, this property true indicates that the car's parking brake is engaged. False indicates the car's parking brake is disengaged.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

PER_DISPLAY_BRIGHTNESS

Property to represent brightness of the displays which are controlled separately. Some cars have one or more displays whose brightness is controlled separately and this property is to inform the brightness of each passenger display. In cars where all displays' brightness is controlled together, they must use DISPLAY_BRIGHTNESS

Only one of PER_DISPLAY_BRIGHTNESS andPER_DISPLAY_BRIGHTNESS should be implemented. If both are available, PER_DISPLAY_BRIGHTNESS is used by AAOS.

The display port uniquely identifies a physical connector on the device for display output, ranging from 0 to 255.

• int32Values[0] Display port
• int32Values[1] Brightness

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 14

PERF_ODOMETER

Current odometer value of the vehicle.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:KILOMETER
Release: Android 13

PERF_REAR_STEERING_ANGLE

Rear bicycle model steering angle for vehicle. Angle is measured in degrees. Left is negative. This property is independent of the angle of the steering wheel. This property must communicate the angle of the rear wheels with respect to the vehicle, not the angle of the steering wheel.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:DEGREES
Release: Android 13

PERF_STEERING_ANGLE

Front bicycle model steering angle for vehicle. Angle is measured in degrees. Left is negative. This property is independent of the angle of the steering wheel. This property must communicate the angle of the front wheels with respect to the vehicle, not the angle of the steering wheel.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:DEGREES
Release: Android 13

PERF_VEHICLE_SPEED

Speed of the vehicle, The value must be positive when the vehicle is moving forward and negative when the vehicle is reversing. This value is independent of gear value (CURRENT_GEAR or GEAR_SELECTION). For example, if GEAR_SELECTION is GEAR_NEUTRAL, PERF_VEHICLE_SPEED is positive when the vehicle is moving forward, negative when reversing, and zero when not moving.

Change mode: CONTINUOUS
Access mode: READ
Unit type: N/A
Unit type: VehicleUnit:METER_PER_SEC
Release: Android 13

PERF_VEHICLE_SPEED_DISPLAY

Speed of the vehicle for displays, Some cars display a slightly slower speed on the speedometer than actual speed.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:METER_PER_SEC
Release: Android 13

POWER_POLICY_GROUP_REQ

Defines a request to set the power policy group used to decide a default power policy per power status transition.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

POWER_POLICY_REQ

Defines a request to apply power policy. VHAL sets this property to change car power policy. Car power policy service subscribes to this property and actually changes the power policy. The request is made by setting the VehiclePropValue with the ID of a power policy which is defined at /vendor/etc/automotive/power_policy.xml If the given ID is not defined, car power policy service ignores the request and the current power policy is maintained.

string: "sample_policy_id" // power policy ID

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

POWER_POLICY_GROUP_REQ

Defines a request to set the power policy group used to decide a default power policy per power status transition. VHAL sets this property with the ID of a power policy group to set the default power policy applied at power status transition. Power policy groups are defined at /vendor/etc/power_policy.xml. If the given ID is not defined, car power policy service ignores the request. Car power policy service subscribes to this property and sets the power policy group. The actual application of power policy takes place when the system power status changes and there is a valid mapped power policy for the new power status.

string: "sample_policy_group_id" // power policy group ID

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

RANGE_REMAINING

Range remaining. Meters remaining of fuel and charge. Range remaining shall account for all energy sources in a vehicle. For example, a hybrid car's range is the sum of the ranges based on fuel and battery. This property is defined as VehiclePropertyAccess.READ_WRITE because a navigation app could update the range if it has a more accurate estimate based on the upcoming route. This property can be implemented as VehiclePropertyAccess.READ only at the OEM's discretion.

Change mode: CONTINUOUS
Access mode: READ_WRITE
Enum type: N/A
Unit type: VehicleUnit:METER
Release: Android 13

READING_LIGHTS_STATE

Return the current status of reading lights.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

READING_LIGHTS_SWITCH

Switch t control the reading lights. This may differ from READING_LIGHTS_STATE if the lights are on because a door is open or due to a voice command. For example, while the switch is in the off or automatic position. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

REAR_FOG_LIGHTS_STATE

Return the current state of the rear fog lights. Only one of FOG_LIGHTS_STATE or REAR_FOG_LIGHTS_STATE can be implemented. See FOG_LIGHTS_STATE

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 13

REAR_FOG_LIGHTS_SWITCH

The setting that the user wants. Only one of FOG_LIGHTS_SWITCH or REAR_FOG_LIGHTS_SWITCH must be implemented. See FOG_LIGHTS_SWITCH to learn more. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READonly.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

REMOVE_USER

Called by the Android System after an Android user was removed. The HAL can use this property to remove the equivalent user. This is write-only cal. The Android System is not expecting a reply from the HAL. Hence, this request should not fail. If the equivalent HAL user cannot be removed, then HAL should mark it as inactive or recover in another way.

The request is made by setting the VehiclePropValue with the contents defined by RemoveUserRequest For example, if system had 3 users (0, 10, and 11) and user 11 was removed, the request would be:

• int32[0] 42 // request id
• int32[1] 11 // (Android user id of the removed user)
• int32[2] 0 // (Android user flags of the removed user)
• int32[3] 10 // current user
• int32[4] 0 // current user flags (none)
• int32[5] 2 // number of users
• int32[6] 0 // first user (user 0)
• int32[7] 0 // first user flags (none)
• int32[8] 10 // second user (user 10)
• int32[9] 0 // second user flags (none)

Change mode: STATIC
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

S 到 Z

SEAT_AIRBAG_ENABLED

Represents feature to enable and disable a seat's ability to deploy airbag(s) when triggered (for example, in a collision). If true, it means the seat's airbags are enabled and, if triggered, they deploy. If true, the seat's airbags are disabled, and they do not deploy in any circumstances. This property does not indicate if the airbags are deployed.

This property can be set to VehiclePropertyAccess.READ read only for the purpose of regulation or safety concerns.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_BACKREST_ANGLE_1_MOVE

Seat backrest angle 1 move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value represents the maximum movement speed of the seat backrest while angling forward. The minInt32Value represents the maximum movement speed of the seat backrest when reclining.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat backrest reaches the positional limit, the value must reset to 0. If the value for SEAT_BACKREST_ANGLE_1_MOVE is 0, no movement is occurring.

This property is represented in a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_BACKREST_ANGLE_1_POS

Seat backrest angle 1 position. Backrest angle 1 is the actuator closest to the bottom of the seat. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the seat backrest's full recline position with regard to the actuator at the bottom of the seat. The maxInt32Value indicates the seat backrest's most upright or forward position with regard to the actuator at the bottom of the seat.

Values between minInt32Value and maxInt32Value indicate a transition state between the full recline and the upright and forward positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_BACKREST_ANGLE_2_MOVE

Seat backrest angle 2 move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat backrest while angling forward. The minInt32Value represents the maximum movement speed of the seat backrest while reclining.

Larger absolute values, positive or negative, indicate a faster movement speed. Once the seat backrest reaches the positional limit, the value must reset to 0. If the value for SEAT_BACKREST_ANGLE_2_MOVE is currently 0, no movement is underway.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A Unit type: N/A
Release: Android 13

SEAT_BACKREST_ANGLE_2_POS

Seat backrest angle 2 position. Backrest angle 2 is the next actuator up from the bottom of the seat.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be #0supported.

The minInt32Value indicates the seat backrest's full recline position with regard to the next actuator in the backrest from the one at the bottom of the seat (see SEAT_BACKREST_ANGLE_1_POS for details). maxInt32Value indicates the seat backrest's most upright and forward position with regard to the next actuator in the backrest from the one at the bottom of the seat (see SEAT_BACKREST_ANGLE_1_POS for details).

Values between minInt32Value and maxInt32Value indicate a transition state between the full recline and upright and forward positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_BELT_BUCKLED

Seatbelt buckled. True indicates belt is buckled. Write access indicates automatic seat buckling capabilities. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_BELT_HEIGHT_MOVE

Seatbelt height move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat belt's shoulder anchor while moving up. The minInt32Value represents the maximum movement speed of the seat belt's shoulder anchor while moving down.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat belt reaches the positional limit, the value must reset to 0. If the value of SEAT_BELT_HEIGHT_MOVE is 0, no movement is underway.

This property is represented as a a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_BELT_HEIGHT_POS

Seatbelt height position. Adjusts the shoulder belt anchor point.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the seat belt's shoulder anchor is at its lowest position. The maxInt32Value indicates the seat belt's shoulder anchor is at its highest position.

Values between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_CUSHION_SIDE_SUPPORT_MOVE

Represents property for movement direction and speed of seat cushion side support.

The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat cushion side support when growing wider (for example, support is decreasing). The minInt32Value represents the maximum movement speed of the seat cushion side support when growing narrower (for example, support is increasing).

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat cushion side support reaches the positional limit, the value must reset to 0. If the value of SEAT_CUSHION_SIDE_SUPPORT_MOVE is 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_CUSHION_SIDE_SUPPORT_POS

Represents property for seat's hipside (bottom cushion's side) support position.

The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value indicates the seat cushion side support is in its widest position (for example, least support). The minInt32Value indicates the seat cushion side support is in its thinnest position (for example, most support).

Values in between minInt32Value and maxInt32Value indicate a transition state between the thinnest and widest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_DEPTH_MOVE

Seat depth move.

The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat while getting deeper The minInt32Value represents the maximum movement speed of the seat while getting shallower.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat backrest reaches the positional limit, the value must reset to 0. If the value for SEAT_DEPTH_MOVE is currently 0, no movement is underway.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_DEPTH_POS

Seat depth position. Sets the seat depth, distance from back rest to front edge of seat.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the seat is in its shallowest position (for example, the position with the smallest distance between the front edge of the seat cushion and the rear end of the seat).

The maxInt32Value indicates the seat is in its deepest position (for example, the position with the largest distance between the front edge of the seat cushion and the rear end of the seat).

Values in between minInt32Value and maxInt32Value indicate a transition state between the shallowest and deepest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only..

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_EASY_ACCESS_ENABLED

Represents property for Seat easy access feature. If true, the seat is automatically adjusted to make it easier for the occupant to enter and exit the vehicle. Each area ID must map to the seat that the user is trying to enter/exit with the help of the easy access feature. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_FOOTWELL_LIGHTS_STATE

Represents property for the seat footwell lights state. SEAT_FOOTWELL_LIGHTS_STATE reflects the current state of the lights at any point in time. This is different from the function of SEAT_FOOTWELL_LIGHTS_SWITCH which represents the position of the switch controlling the lights.

Therefore, SEAT_FOOTWELL_LIGHTS_STATE may not match the value of SEAT_FOOTWELL_LIGHTS_SWITCH (for example, SEAT_FOOTWELL_LIGHTS_SWITCH=AUTOMATIC and SEAT_FOOTWELL_LIGHTS_SWITCH=ON).

This property should only be implemented if SEAT_FOOTWELL_LIGHTS_STATE 's value may be different from that of CABIN_LIGHTS_STATE.

For each supported area ID, the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of VehicleLightState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 14

SEAT_FOOTWELL_LIGHTS_SWITCH

Represents property for the seat footwell lights switch. SEAT_FOOTWELL_LIGHTS_SWITCH represents the position of the switch controlling the lights. This is different from the function of SEAT_FOOTWELL_LIGHTS_STATE which reflects the current state of the lights at any point in time. Therefore, SEAT_FOOTWELL_LIGHTS_SWITCH may not match the value of SEAT_FOOTWELL_LIGHTS_STATE (for example, SEAT_FOOTWELL_LIGHTS_SWITCH=AUTOMATIC and SEAT_FOOTWELL_LIGHTS_SWITCH=ON).

This property should only be implemented if SEAT_FOOTWELL_LIGHTS_SWITCH's value may be different from that of CABIN_LIGHTS_SWITCH.

For each supported area ID, the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of VehicleLightSwitch are supported.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 13

SEAT_FORE_AFT_MOVE

Seat fore and aft move. This property moves the entire seat forward/backward in the direction that it is facing.

The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat while moving forward. The minInt32Value represents the maximum movement speed of the seat while moving backward.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat reaches the positional limit, the value must reset to 0. If the value of SEAT_FORE_AFT_MOVE is 0, no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_FORE_AFT_POS

Seat fore and aft position. Sets the seat position forward and backward.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the seat is at its rearward-most linear position. The maxInt32Value indicates the seat is at its forward-most linear position. Values between minInt32Value and maxInt32Value indicate a transition state between the closest and farthest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_ANGLE_MOVE

Headrest angle move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat's headrest while moving into an upright or forward position. The minInt32Value represents the maximum movement speed of the seat's headrest while moving into a shallow position.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat's headrest reaches the positional limit, the value must reset to 0. If the value of SEAT_HEADREST_ANGLE_MOVE is 0, thenno movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only..

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_ANGLE_POS

Headrest angle position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the headrest is in its full recline position. The maxInt32Value indicates the headrest is in its most upright and forward position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the full recline and most upright and forward positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_FORE_AFT_MOVE

Headrest fore and aft move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat's headrest while moving forward. The minInt32Value represents the maximum movement speed of the seat's headrest while moving backward.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat's headrest reaches the positional limit, the value must reset to 0. If the value of SEAT_HEADREST_FORE_AFT_MOVE is 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_FORE_AFT_POS

Headrest fore and aft position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the headrest is in its rearward-most linear position. The maxInt32Value indicates the headrest is in its forward-most linear position.

Values between minInt32Value and maxInt32Value indicate a transition state between the forward and backward positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_HEIGHT_MOVE

Headrest height move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat's headrest while moving up. The minInt32Value represents the maximum movement speed of the seat's headrest while moving down.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat's headrest reaches the positional limit, the value must reset to 0. If the value for SEAT_HEADREST_HEIGHT_MOVE is 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_HEIGHT_POS

(Deprecated) Headrest height position.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEADREST_HEIGHT_POS_V2

Headrest height position. Sets the headrest height for supported seats. VehiclePropConfig.areaConfigs specifies which seats are supported.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the headrest is in its lowest position. The maxInt32Value indicates the headrest is in its highest position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_HEIGHT_MOVE

Seat height move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

maxInt32Value represents the maximum movement speed of the seat when moving up.

minInt32Value represents the maximum movement speed of the seat when moving down.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat reaches the positional limit, the value must reset to 0. If the value of SEAT_HEIGHT_MOVE value is 0, no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_HEIGHT_POS

Seat height position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the seat is in its lowest position. The maxInt32Value indicates the seat is in its highest position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_LUMBAR_FORE_AFT_MOVE

Lumbar fore and aft move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat's lumbar support while moving forward. The minInt32Value represents the maximum movement speed of the seat's lumbar support while moving backward.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat's lumbar support reaches the positional limit, the value must reset to 0. If the value of SEAT_LUMBAR_FORE_AFT_MOVE is 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_LUMBAR_FORE_AFT_POS

Lumber fore and aft position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The minInt32Value indicates the lumbar support is in its rearward most position (for example, least supportive position). The maxInt32Value indicates the lumbar support is in its forward most position (for example, most supportive position).

Values in between minInt32Value and maxInt32Value indicate a transition state between the forward and rearward positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access type: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_LUMBAR_SIDE_SUPPORT_MOVE

Lumbar side support move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported.

The maxInt32Value represents the maximum movement speed of the seat's lumbar side support while getting wider. The minInt32Value represents the maximum movement speed of the seat's lumbar side support while getting thinner.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat's lumbar side support reaches the positional limit, the value must reset to 0. If the value of SEAT_LUMBAR_SIDE_SUPPORT_MOVE 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access type: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_LUMBAR_SIDE_SUPPORT_POS

Lumbar side support position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the lumbar side support is in its thinnest position (for example, most support). The maxInt32Value indicates the lumbar side support is in its widest position (for example, least support).

Values in between minInt32Value and maxInt32Value indicate a transition state between the thinnest and widest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access type: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_LUMBAR_VERTICAL_MOVE

Represents property for vertical movement direction and speed of seat lumbar support.

The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the lumbar support is moving at the fastest upward speed. The minInt32Value indicates the lumbar support is moving at the fastest down speed.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat cushion side support reaches the positional limit, the value must reset to 0. If the value of SEAT_LUMBAR_VERTICAL_MOVE's is 0, then no movement is occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_LUMBAR_VERTICAL_POS

Represents property for seat's lumbar support vertical position. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. maxInt32Value indicates the lumbar support's highest position. minInt32Value indicates the lumbar support's lowest position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_MEMORY_SELECT

This parameter selects the memory preset to use to select the seat position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value is always 0, and the maxInt32Value determines the number of seat preset memory slots available (for example, numSeatPresets - 1). For instance, if the driver's seat has three memory presets, the maxInt32Value is two. When the user selects a preset, the desired preset number (0, 1, or 2) is set.

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_MEMORY_SET

This setting allows the user to save the current seat position settings into the selected preset slot. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. The minInt32Value must be 0, and the maxInt32Value for each seat position must match the maxInt32Value for SEAT_MEMORY_SELECT

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_OCCUPANCY

Indicates if a specific seat is occupied, to the best of the car's ability to determine. Valid values are from the VehicleSeatOccupancyState enum.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleSeatOccupancyState
Unit type: N/A
Release: Android 13

SEAT_TILT_MOVE

Seat tilt move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value represents the maximum movement speed of the front edge of the seat while moving up. The minInt32Value represents the maximum movement speed of the front edge of the seat while moving down.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the seat bottom reaches the positional limit, the value must reset to 0. If SEAT_TILT_MOVE's value is currently 0, no movement is underway.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SEAT_TILT_POS

Seat tilt position. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the seat bottom is angled at its lowest angular position. This corresponds to the seat's front edge at its lowest possible position relative to the rear end of the seat. The maxInt32Value indicates the seat bottom is angled at its highest angular position. This corresponds to the seat's front edge at its highest possible position relative to the rear end of the seat.

Values in between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SEAT_WALK_IN_POS

Represents property that indicates the current walk-in position of the seat. The minInt32Value indicates the normal seat position. The minInt32Value must be 0. The maxInt32Value indicates the seat is in the full walk-in position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the normal and walk-in positions.

This property is represented as a specified range of relative positions.

The area ID must match the seat that actually moves when the walk-in feature activates, not the intended seat the passengers will sit in.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can

implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SHUTDOWN_REQUEST

Request the head unit to be shu down.

This is required for executing a task when the head unit is powered off (remote task feature). After the head unit is powered-on to execute the task, the head unit should be shut down. The head unit sends this message once the task is finished.

This property doesn't apply when a user wants to shut down the head unit.

This usually involves telling a separate system outside the head unit (for instance a power controller) to prepare to shut down the head unit.

The external system must validate that this request is valid by checking if the vehicle is in use. If a user enters the vehicle after a SHUTDOWN_REQUEST is sent, then the system must ignore this request. It is recommended to store a VehicleInUse property in the power controller and exposes it through VEHICLE_IN_USE property. A shutdown request must be ignored if VehicleInUse is true.

If allowed, the external system sends a shutdown signal to the head unit, which causes VHAL to send SHUTDOWN_PREPARE message to Android. Android will then start the shut down process by handling the message.

This property is only for issuing a request and only supports writing. Every time this property value is set, the request to shutdown is issued no matter what the current property value is. The current property value is meaningless.

Since this property is write-only, subscribing is not allowed and no property change event is generated.

The value to set indicates the shutdown option, it must be one of {@code VehicleApPowerStateShutdownParam} For example, VehicleApPowerStateShutdownParam.SLEEP_IMMEDIATELY. This shutdown option might not be honored if the system doesn't support such option. In such a case, an error is not returned.

For configuration information, VehiclePropConfig.configArray must have bit flag combining values in {@code VehicleApPowerStateConfigFlag} to indicate which shutdown options are supported.

Returns error if failed to send the shutdown request to the other system.

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: VehicleApPowerStateShutdownParam>
Unit type: N/A
Release: Android 14

STEERING_WHEEL_DEPTH_MOVE

Steering wheel depth movement. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All values between minInt32Value and maxInt32Value must be supported.

The maxInt32Value indicates the steering wheel moving away from the driver. The minInt32Value indicates the steering wheel moving towards the driver.

Larger integers, either positive or negative, indicate a faster movement speed. Once the steering wheel reaches the positional limit, the value must reset to 0. If the value of STEERING_WHEEL_DEPTH_MOVE is currently 0, no movement is underway.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_DEPTH_POS

Steering wheel depth position. All steering wheel properties' unique ids start from 0x0BE0.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All values between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the steering wheel position furthest from the driver. The minInt32Value indicates the steering wheel position closest to the driver.

Values in between minInt32Value and maxInt32Value indicate a transition state between the

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_EASY_ACCESS_ENABLED

Steering wheel easy access feature enabled. If true, the driver's steering wheel is automatically adjusted to make it easier for the driver to enter and exit the vehicle.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_HEIGHT_MOVE

Steering wheel height movement. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All values between minInt32Value and maxInt32Value must be supported.

The maxInt32Value indicates the steering wheel moving up. The minInt32Value indicates the steering wheel moving down.

Larger integers, either positive or negative, indicate a faster movement speed. Once the steering wheel reaches the positional limit, the value must reset to 0. If STEERING_WHEEL_HEIGHT_MOVE's value is currently 0, then that means there is no movement currently occurring.

This property is represented as a specified range of relative movement speeds.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_HEIGHT_POS

Steering wheel height position.

The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. All values between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the steering wheel being in the highest position. The minInt32Value indicates the steering wheel being in the lowest position.

Values in between minInt32Value and maxInt32Value indicate a transition state between the lowest and highest positions.

This property is represented as a specified range of relative positions.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_LIGHTS_STATE

Steering wheel lights state. Represents the current state of the steering wheel lights. This is different from STEERING_WHEEL_LIGHTS_SWITCH which represents the position of the switch controlling the lights. Therefore, STEERING_WHEEL_LIGHTS_STATE may not match the value of STEERING_WHEEL_LIGHTS_SWITCH (for example, STEERING_WHEEL_LIGHTS_SWITCH=AUTOMATIC and STEERING_WHEEL_LIGHTS_STATE=ON).

This property should only be implemented if STEERING_WHEEL_LIGHTS_STATE's value may be different from that of CABIN_LIGHTS_STATE.

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of VehicleLightState are supported.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleLightState
Unit type: N/A
Release: Android 14

STEERING_WHEEL_LIGHTS_SWITCH

Steering wheel lights switch. Represents the position of the switch controlling the steering wheel lights. This differs from , which represents the current state of the steering wheel lights. Therefore, STEERING_WHEEL_LIGHTS_SWITCH may not match the value of STEERING_WHEEL_LIGHTS_STATE. For example, STEERING_WHEEL_LIGHTS_SWITCH=AUTOMATIC and STEERING_WHEEL_LIGHTS_STATE=ON.

This property should only be implemented if the value for STEERING_WHEEL_LIGHTS_SWITCH can differ from that of CABIN_LIGHTS_SWITCH.

For the global area ID (0), the VehicleAreaConfig#supportedEnumValues must be defined unless all enum values of VehicleLightSwitch are supported.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleLightSwitch
Unit type: N/A
Release: Android 14

STEERING_WHEEL_LOCKED

Steering wheel locked. If true, the steering wheel's position is locked and not changeable. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only./p>

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STEERING_WHEEL_THEFT_LOCK_ENABLED

Steering wheel theft lock feature enabled. If true, the steering wheel locks automatically to prevent theft in certain situations. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

STORAGE_ENCRYPTION_BINDING_SEED

External encryption binding seed. This value is mixed with the local key storage encryption key. This property holds 16 bytes, and is expected to be persisted on an ECU separate from the IVI. The property is initially set by AAOS, who generates it using a CSRNG. AAOS then reads the property on subsequent boots. The binding seed is expected to be reliably persisted. Any loss of the seed results in a factory reset of the IVI.

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

SUPPORT_CUSTOMIZE_VENDOR_PERMISSION

Support customize permissions for vendor properties.

Implement this property if VHAL support customize vendor permissions feature. VehiclePropConfig.configArray is used to indicate vendor properties and permissions which selected for this vendor property. The permission must be one of enum in VehicleVendorPermission. The configArray is set as follows, configArray[n]: propId : property ID for the vendor property where configArray[n+1] is an enum in VehicleVendorPermission and indicates the permission for reading the value of the property.

configArray[n+2] is an enum in VehicleVendorPermission and indicates the permission for writing a value of the property. For example:

configArray: { vendor_prop_1, PERMISSION_VENDOR_SEAT_READ, PERMISSION_VENDOR_SEAT_WRITE, vendor_prop_2, PERMISSION_VENDOR_INFO, PERMISSION_NOT_ACCESSIBLE, }

If vendor properties are not in this array, they have the default vendor permission. If vendor chose PERMISSION_NOT_ACCESSIBLE, Android does not have access to the property. In the example, Android can not write a value for vendor_prop_2.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

SUPPORTED_PROPERTY_IDS

(Deprecated) List of all supported property IDs.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 14

SWITCH_USER

Defines a request to switch the foreground Android user.

This property is used primarily by the Android system to inform the HAL that the current foreground Android user is switching, but it could also be used by the HAL to request the Android system to switch users. When the request is made by Android, it sets a VehiclePropValue and the HAL must respond with a property change event. When the HAL makes the request, it must also do it through a property change event (the main difference is that the request id is positive in the former case, and negative in the latter). The SwitchUserMessageType also differs.

The format of both requests is defined by SwitchUserRequest and the format of the response (when needed) is defined by SwitchUserResponse. How the HAL (or Android system) should proceed depends on the message type (which is defined by the SwitchUserMessageType parameter), as defined below.

• LEGACY_ANDROID_SWITCH Called by the Android system to indicate the Android user is about to change, when the change request was made in a way that is not integrated with the HAL (for example, through adb shell am switch-user). The HAL can switch its internal user once it receives this request, but it doesn't need to reply back to the Android system. If its internal user cannot be changed for some reason, then it must wait for the SWITCH_USER(type=ANDROID_POST_SWITCH) call to recover (for example, it could issue a SWITCH_USER(type=VEHICLE_REQUEST) to switch back to the previous user). Ideally it should never fail (as switching back could confuse the end user).
  For example, if the system have users (0, 10, 11) and it's switching from 0 to 11 (where none of them have any special flag), the request would be:
  
  • int32[0] 42 // request id
  • int32[1] 1 // SwitchUserMessageType::LEGACY_ANDROID_SWITCH
  • int32[2] 11 // target user id
  • int32[3] 0 // target user flags (none)
  • int32[4] 10 // current user
  • int32[5] 0 // current user flags (none)
  • int32[6] 3 // number of users
  • int32[7] 0 // user #0 (Android user id 0)
  • int32[8] 0 // flags of user #0 (none)
  • int32[9] 10 // user #1 (Android user id 10)
  • int32[10] 0 // flags of user #1 (none)
  • int32[11] 11 // user #2 (Android user id 11)
  • int32[12] 0 // flags of user #2 (none)
• ANDROID_SWITCH Called by the Android system to indicate the Android user is about to change, but Android waits for the HAL's response (up to some time) before proceeding. The HAL must switch its internal user once it receives this request, then respond back to Android with a SWITCH_USER(type=VEHICLE_RESPONSE) indicating whether its internal user was switched or not (through the SwitchUserStatus enum). For example, if Android has users (0, 10, 11) and it's switching from 10 to 11 (where none of them have any special flag), the request would be:
  • int32[0] 42 // request id
  • int32[1] 2 // SwitchUserMessageType::ANDROID_SWITCH
  • int32[2] 11 // target user id
  • int32[3] 0 // target user flags (none)
  • int32[4] 10 // current user
  • int32[5] 0 // current user flags (none)
  • int32[6] 3 // number of users
  • int32[7] 0 // first user (user 0)
  • int32[8] 1 // first user flags (SYSTEM)
  • int32[9] 10 // second user (user 10)
  • int32[10] 0 // second user flags (none)
  • int32[11] 11 // 3rd user (user 11)
  • int32[12] 0 // 3rd user flags (none)

  If the request succeeds, the HAL must update the property with:

  • int32[0] 42 // request id
  • int32[1] 3 // messageType: SwitchUserMessageType::VEHICLE_RESPONSE
  • int32[2] 1 // status: SwitchUserStatus::SUCCESS

  If the request fails, the response would be something like:

  • int32[0] 42 // request id
  • int32[1] 3 // messageType: SwitchUserMessageType::VEHICLE_RESPONSE
  • int32[2] 2 // status: SwitchUserStatus::FAILURE string: "108-D'OH!"
  • OEM-specific error message
• VEHICLE_RESPONSE Called by the HAL to indicate whether a request of type ANDROID_SWITCH should proceed or abort. See also ANDROID_SWITCH.
• VEHICLE_REQUEST Called by the HAL to request that the current foreground Android user is switched. This is useful in situations where Android started as one user, but the vehicle identified the driver as another user. For example, user A unlocked the car using the key fob of user B. The INITIAL_USER_INFO request returned user B, but then a face recognition subsubsystem identified the user as A. The HAL makes this request by a property change event (passing a negative request id), and the Android system response is to issue an ANDROID_POST_SWITCH call which the same request id. For example, if the current foreground Android user is 10 and the HAL asked to switch to 11, the request would be:
  • int32[0] -108 // request id
  • int32[1] 4 // messageType: SwitchUserMessageType::VEHICLE_REQUEST
  • int32[2] 11 // Android user id

  If the request succeeded and Android has three users (0, 10, and 11), the response would be:

  • int32[0] -108 // request id
  • int32[1] 5 // messageType: SwitchUserMessageType::ANDROID_POST_SWITCH
  • int32[2] 11 // target user id
  • int32[3] 0 // target user id flags (none)
  • int32[4] 11 // current user
  • int32[5] 0 // current user flags (none)
  • int32[6] 3 // number of users
  • int32[7] 0 // first user (user 0)
  • int32[8] 0 // first user flags (none)
  • int32[9] 10 // second user (user 10)
  • int32[10] 4 // second user flags (none)
  • int32[11] 11 // third user (user 11)
  • int32[12] 3 // third user flags (none)

  The current and target user ids are the same. If the request fails, then they would differ. For example, the target user would be 11 and the current user would remain 10.

• ANDROID_POST_SWITCH Called by the Android system after a request to switch a user was made. This property is called after switch requests of any type (for example, >code>LEGACY_ANDROID_SWITCH, >code>ANDROID_SWITCH, or VEHICLE_REQUEST) and can be used to determine if the request succeeded or failed.
  • When it succeeds, it's called when the Android user is in the unlocked state and the value of the current and target users ids in the response are the same. This is equivalent to receiving an Intent.ACTION_USER_UNLOCKED in an Android app.
  • When it fails, it's called right away and the value of the current and target users ids in the response differ (since the current user didn't change to the target).
  • If a new switch request is made before the HAL responded to the previous one or before the user was unlocked, then the ANDROID_POST_SWITCH request is not made. For example, the driver might accidentally switch to the wrong user, which has lock credentials, and then switch to the correct user before entering the credentials.

  The HAL can update its internal state once it receives this request, but it needn't reply to the Android system.

  • Request. The first N values as defined by INITIAL_USER_INFO (where the request-specific value at index 1 is SwitchUserMessageType::ANDROID_POST_SWITCH), then two more values for the target user id (for example, the Android user id that was requested to be switched to) and its flags (as defined by UserFlags).
  • Response: none. For example, see VEHICLE_REQUEST

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

TIRE_PRESSURE

Tire pressure. Each tire is identified by its areaConfig.areaId config. The respective minFloatValue and maxFloatValue are used to store the OEM- recommended pressure range. Values for minFloatValue and maxFloatValue in VehicleAreaConfig must be defined.

The minFloatValue in the areaConfig data represents the lower bound of the recommended tire pressure. The maxFloatValue in the areaConfig data represents the upper bound of the recommended tire pressure. For example, this areaConfig indicates the recommended tire pressure of left_front tire as from 200.0kPa to 240.0kPa.

.areaConfigs: { VehicleAreaConfig { .areaId: VehicleAreaWheel::LEFT_FRONT, .minFloatValue: 200.0, .maxFloatValue: 240.0, } }

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:KILOPASCAL
Release: Android 13

TIRE_PRESSURE_DISPLAY_UNITS

Tire pressure units for display. Indicates which units the car is using to display tire pressure to the user. For example, PSI, Bar or Kilopascal. VehiclePropConfig.configArray is used to indicate the supported pressure display units. Pressure units are defined in VehicleUnit. For example, configArray[0]: KILOPASCAL configArray[1]: PSI configArray[2]: BAR

If updating TIRE_PRESSURE_DISPLAY_UNITS affects the values of other *_DISPLAY_UNITS properties, then their values must be updated and communicated to the AAOS framework as well. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as only./p>

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: VehicleUnit
Unit type: N/A
Release: Android 13

TRACTION_CONTROL_ACTIVE

Set to true when traction control (TC) is active and reset to false when TC is off. This property can be intermittently set (pulse) based on the real-time state of the TC system.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

TRAILER_PRESENT

Returns the trailer state of the car.

Change mode: ON_CHANGE
Access mode: READ
Enum type: TrailerState
Unit type: N/A
Release: Android 13

TURN_SIGNAL_STATE

State of the vehicles turn signals.

Change mode: ON_CHANGE
Access mode: READ
Enum type: VehicleTurnSignal
Unit type: N/A
Release: Android 13

USER_IDENTIFICATION_ASSOCIATION

Property used to associate (or query the association) the current user with vehicle-specific identification mechanisms (such as key FOB).

This is an optional user management property. The OEM can still support user management without defining it. In fact, this property could be used without supporting the core user-related functions described on INITIAL_USER_INFO.

To query the association, the Android system gets the property, passing a VehiclePropValue containing the types of associations are being queried, as defined by UserIdentificationGetRequest. The HAL must return right away, returning a VehiclePropValue with a UserIdentificationResponse.

Notice that user identification took place while the system was booting up. takehe VHAL implementation should only return the already identified association (such as the key FOB used to unlock the car), instead of starting a new association from the get call.

To associate types, the Android system sets the property, passing a VehiclePropValue containing the types and values of associations being set, as defined by the UserIdentificationSetRequest.

The HAL then uses a property change event (whose VehiclePropValue is defined by UserIdentificationResponse) indicating the current status of the types after the request.

For example, to query if the current user (10) is associated with the FOB that unlocked the car and a custom mechanism provided by the OEM, the request is:

• int32[0] 42 // request id
• int32[1] 10 (Android user id)
• int32[2] 0 (Android user flags)
• int32[3] 2 (number of types queried)
• int32[4] 1 (first type queried, UserIdentificationAssociationType::KEY_FOB)
• int32[5] 101 (second type queried, UserIdentificationAssociationType::CUSTOM_1)

If the user is associated with the FOB but not with the custom mechanism, the response is:

• int32[0] 42 // request id
• int32[1] 2 (number of associations in the response)
• int32[2] 1 (first type: UserIdentificationAssociationType::KEY_FOB)
• int32[3] 2 (first value: UserIdentificationAssociationValue::ASSOCIATED_CURRENT_USER)
• int32[4] 101 (first type: UserIdentificationAssociationType::CUSTOM_1)
• int32[5] 4 (second value: UserIdentificationAssociationValue::NOT_ASSOCIATED_ANY_USER)

Then to associate the user with the custom mechanism, a set request is made:

• int32[0] 43 // request id
• int32[1] 10 (Android user id)
• int32[2] 0 (Android user flags)
• int32[3] 1 (number of associations being set)
• int32[4] 101 (first type: UserIdentificationAssociationType::CUSTOM_1)

If the request succeeded, the response would be:

• int32[0] 43 // request id
• int32[1] 1 (number of associations in the response)
• int32[2] 101 (first type: UserIdentificationAssociationType::CUSTOM_1)
• int32[3] 1 (first value: UserIdentificationAssociationValue::ASSOCIATED_CURRENT_USER)

The set request adds associations but doesn't remove the existing associations. In the previous example, the end state would be two associations (FOB and CUSTOM_1). To associate the user with just CUSTOM_1 but not FOB, then the request would have been:

• int32[0] 43 // request id
• int32[1] 10 (Android user id)
• int32[2] 2 (number of types set)
• int32[3] 1 (first type: UserIdentificationAssociationType::KEY_FOB)
• int32[4] 2 (first value: UserIdentificationAssociationValue::DISASSOCIATE_CURRENT_USER)
• int32[5] 101 (second type: UserIdentificationAssociationType::CUSTOM_1)
• int32[6] 1 (second value: UserIdentificationAssociationValue::ASSOCIATE_CURRENT_USER)

Change mode: ON_CHANGE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

VEHICLE_CURB_WEIGHT

Returns the vehicle's curb weight in kilograms. Curb weight is the total weight of the vehicle with standard equipment and all necessary operating consumables such as motor oil, transmission oil, brake fluid, coolant, air conditioning refrigerant, and weight of fuel at nominal tank capacity while not loaded with either passengers or cargo.

configArray[0] is used to specify the vehicle's gross weight in kilograms. The vehicle's gross weight is the maximum operating weight of the vehicle as specified by the manufacturer including the vehicle's chassis, body, engine, engine fluids, fuel, accessories, driver, passengers and cargo but excluding that of any trailers.

Change mode: STATIC
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:KILOGRAM
Release: Android 13

VEHICLE_IN_USE

Indicates if the vehicle is in use. In use means a human user is present and intendeds to use the vehicle. This doesn't necessarily mean the human user is in the vehicle. For example, if the human user unlocks the vehicle remotely, the vehicle is considered to be in use. If this property is supported:

• Each time the user powers on the vehicle or the system detects the user is present, VEHICLE_IN_USE must be set to true. Each time the user powers off the vehicle or the system detects the user is not present, VEHICLE_IN_USE must be set to false.
• If the user powers off the vehicle or the system detects the user is not present, VEHICLE_IN_USE must be set to false.
• If the user powers on the vehicle or the system detects the user is present, VEHICLE_IN_USE must be set to true.

This property differs from AP_POWER_BOOTUP_REASON in the sense that AP_POWER_BOOTUP_REASON is only set once during system boot. However, this property might change multiple times during a system boot cycle. For example, a device is currently not in use. The system bootup to execute a remote task. VEHICLE_IN_USE is false. While the remote task is executing, the user enters the vehicle and powers on the vehicle. VEHICLE_IN_USE is set to true. After a driving session, user powers off the vehicle, VEHICLE_IN_USE is set to false.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 14

VEHICLE_MAP_SERVICE

Vehicle Maps Service (VMS) message. This property uses MIXED data to communicate VMS messages. Its contents are to be interpreted as follows. The indices defined in VmsMessageIntegerValuesInde are used to read from int32Values. bytes is a serialized VMS message as defined in the VMS protocol, which is opaque to the framework. IVehicle#get must always return StatusCode::NOT_AVAILABLE.

Change mode: ON_CHANGEREAD_WRITE
Access mode: READ_WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

VEHICLE_SPEED_DISPLAY_UNITS

Speed units for display. Indicates the type of units used to display speed to the user. For example, m/s, km/h, or mph. VehiclePropConfig.configArray indicates the supported speed display units. Pressure units are defined in VehicleUnit. For example:

.configArray: { VehicleUnit::METER_PER_SEC, VehicleUnit::KILOMETERS_PER_HOUR, VehicleUnit::MILES_PER_HOUR }

• configArray[0] METER_PER_SEC
• configArray[1] MILES_PER_HOUR
• configArray[2] KILOMETERS_PER_HOUR

If updating VEHICLE_SPEED_DISPLAY_UNITS affects the values of other *_DISPLAY_UNITS properties, then those values must be updated and communicated to the AAOS framework.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

VHAL_HEARTBEAT

Defines an event that VHAL signals to Car Watchdog as a heartbeat. If VHAL supports this property, VHAL should write system uptime to this property at every three seconds. Car Watchdog subscribes to this property and checks if the property is updated every three seconds. With the buffer time of three seconds, Car Watchdog waits for a heartbeat to be signaled up to six seconds from the last heartbeat. If not, Car Watchdog considers VHAL unhealthy and terminates it. If this property is not supported by VHAL, Car Watchdog doesn't check VHAL health status.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

WATCHDOG_ALIVE

Defines an event that Car Watchdog updates to indicate it's active. Car Watchdog sets this property to system uptime in milliseconds at every three seconds. While booting, the update could take longer.

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

WATCHDOG_TERMINATED_PROCESS

Defines a process terminated by Car Watchdog and the reason for the termination.

int32Values[0] 1  // ProcessTerminationReason showing why a process is terminated. string: "/system/bin/log" // Process execution command

Change mode: ON_CHANGE
Access mode: WRITE
Enum type: N/A
Unit type: N/A
Release: Android 13

WHEEL_TICK

Reports wheel ticks. The first element in the vector is a reset count. A reset indicates previous tick counts are not comparable with this and future ones. Some sort of discontinuity in tick counting has occurred.

The next four elements represent ticks for individual wheels in the following order:

1. Front left
2. Front right
3. Rear right
4. Rear left

All tick counts are cumulative. Tick counts increment when the vehicle moves forward, and decrement when the vehicle moves backward. The ticks should be reset to 0 when the vehicle is started.

• int64Values[0] Reset count
• int64Values[1] Front left ticks
• int64Values[2] Front right ticks
• int64Values[3] Rear right ticks
• int64Values[4] Rear left ticks

configArray is used to indicate the micrometers-per-wheel-tick value and which wheels are supported configArray is set as follows:

configArray[0], bits [0:3] Supported wheels

Uses enum Wheel. For example, if all wheels are supported, then:

• configArray[0] VehicleAreaWheel::LEFT_FRONT | VehicleAreaWheel::RIGHT_FRONT | VehicleAreaWheel::LEFT_REAR | VehicleAreaWheel::RIGHT_REAR
• configArray[1] Micrometers per front left wheel tick
• configArray[2] Micrometers per front right wheel tick
• configArray[3] Micrometers per rear right wheel tick
• configArray[4] Micrometers per rear left wheel tick.

If a wheel is not supported, its value shall always be set to 0.

The VehiclePropValue.timestamp must be filled in.

Change mode: CONTINUOUS
Access mode: READ
Enum type: N/A
Unit type: N/A
Release: Android 13

WINDOW_LOCK

Window child lock. True indicates the window is child-locked. This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

WINDOW_MOVE

Window move. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The maxInt32Value indicates the window is opening in plane/closing in the out of plane direction at the fastest speed. The minInt32Value indicates the window is closing in plane/opening in the out of plane direction at the fastest speed.

Larger absolute values, either positive or negative, indicate a faster movement speed. Once the window reaches the positional limit, the value must reset to 0. If the value of WINDOW_MOVE is 0, no movement is underway. This property is represented in a specified range of relative movement speeds.

For a window that may open out of plane (a vent mode of sunroof), this parameter works as follows. If:

• Sunroof is open:
  • Max Open the sunroof further, stop automatically when fully open.
  • Min Close the sunroof, stop automatically when sunroof is closed.
• Vent is open:
  • Max Close the vent, stop automatically stop when vent is closed.
  • Min Open the vent further, stop automatically when vent is fully open.
• Sunroof is closed:
  • Max Open the sunroof, stop automatically when sunroof is fully open.
  • Min Open the vent, stop automatically when vent is fully open.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

WINDOW_POS

Window position. The maxInt32Value and minInt32Value in each VehicleAreaConfig must be defined. All integers between minInt32Value and maxInt32Value must be supported. The minInt32Value indicates the window is closed or fully open out of plane. If the window cannot open out of plane, then minInt32Value is the position of the window when fully closed and must be 0. If the window can open out of plane, the minInt32Value indicates the window is fully open in its position out of plane and is a negative value. See the example below for a more detailed explanation. The maxInt32Value indicates the window is fully open.

Values in between minInt32Value and maxInt32Value indicate a transition state between the closed/fully open out-of-plane and fully open positions. This property is not in any specific unit but in a specified range of relative positions. For example, this is how the property should work for a window that can move out of plane: For a window that may open out of plane (vent mode of sunroof) this parameter works with negative values as follows:

• Max Sunroof fully open (0 for sunroof closed).
• Min Sunroof vent fully open (0 for sunroof closed).

In this mode, 0 indicates the window is closed.

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: N/A
Unit type: N/A
Release: Android 13

WINDSHIELD_WIPERS_PERIOD

Windshield wipers period (milliseconds). Returns the instantaneous time period for one full cycle of the windshield wipers in milliseconds. A full cycle is defined as a wiper moving from and returning to the rest position. When an intermittent wiper setting is selected, this property value must be set to 0 during the pause period of the intermittent wiping. The maxInt32Value and minInt32Value in VehicleAreaConfig must be defined. The maxInt32Value for each area ID must specify the longest wiper period. The minInt32Value must be set to 0 for each area ID.

Change mode: ON_CHANGE
Access mode: READ
Enum type: N/A
Unit type: VehicleUnit:MILLI_SECS
Release: Android 14

WINDSHIELD_WIPERS_STATE

Windshield wipers state. Returns the current state of the windshield wipers. The value of WINDSHIELD_WIPERS_STATE may not match the value of WINDSHIELD_WIPERS_SWITCH For example, WINDSHIELD_WIPERS_STATE: ON and WINDSHIELD_WIPERS_SWITCH: WindshieldWipersSwitch#AUTO If WINDSHIELD_WIPERS_STATE: ON and WINDSHIELD_WIPERS_PERIOD is implemented, then WINDSHIELD_WIPERS_PERIOD must reflect the time period of one full cycle of the wipers.

For each supported area ID, the VehicleAreaConfig#supportedEnumValues array must be defined unless all states in WindshieldWipersState are supported (including OTHER, which is not recommended).

Change mode: ON_CHANGE
Access mode: READ
Enum type: WindshieldWipersState
Unit type: N/A
Release: Android 14

WINDSHIELD_WIPERS_SWITCH

Windshield wipers switch. Represents the position of the switch controlling the windshield wipers. The value of WINDSHIELD_WIPERS_SWITCH may not match the value of WINDSHIELD_WIPERS_STATE For example, WINDSHIELD_WIPERS_SWITCH: AUTO and WINDSHIELD_WIPERS_STATE: WindshieldWipersState#ON For each supported area ID, the VehicleAreaConfig#supportedEnumValues array must be defined unless all states in WindshieldWipersSwitch are supported (including OTHER, which is not recommended).

This property is defined as VehiclePropertyAccess.READ_WRITE, but OEMs can implement it as VehiclePropertyAccess.READ only. If this property is implemented as VehiclePropertyAccess.READ_WRITE and the OTHER state is listed in the VehicleAreaConfig#supportedEnumValues array, then OTHER is not a supported value for writing It is only a supported value for reading.

Change mode: ON_CHANGE
Access mode: READ_WRITE/READ
Enum type: WindshieldWipersSwitch
Unit type: N/A
Release: Android 14